KSZ8873MLL Micrel Inc, KSZ8873MLL Datasheet - Page 29
![IC ETHERNET SWITCH 3PORT 64-LQFP](/photos/6/81/68149/64-lqfp-micrel_sml.jpg)
KSZ8873MLL
Manufacturer Part Number
KSZ8873MLL
Description
IC ETHERNET SWITCH 3PORT 64-LQFP
Manufacturer
Micrel Inc
Specifications of KSZ8873MLL
Data Rate
100Mbps
Controller Type
Ethernet Switch Controller
Interface
MII
Voltage - Supply
1.8V, 2.5V, 3.3V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
No. Of Ports
3
Ethernet Type
IEEE 802.3u
Supply Current
115mA
Supply Voltage Range
2.5V, 3.3V
Digital Ic Case Style
LQFP
No. Of Pins
64
Svhc
No SVHC (15-Dec-2010)
Base
RoHS Compliant
Number Of Primary Switch Ports
3
Internal Memory Buffer Size
32
Fiber Support
No
Integrated Led Drivers
Yes
Phy/transceiver Interface
MII
Power Supply Type
Analog/Digital
Data Rate (typ)
10/100Mbps
Vlan Support
Yes
Operating Temperature (max)
70C
Operating Temperature (min)
0C
Mounting
Surface Mount
Jtag Support
No
Operating Supply Voltage (max)
1.89/3.465V
Operating Temperature Classification
Commercial
Interface Type
MII, RMII
Operating Temperature Range
0°C To +70°C
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
576-3459
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
KSZ8873MLL
Manufacturer:
Micrel Inc
Quantity:
1 934
Company:
Part Number:
KSZ8873MLL
Manufacturer:
ADI
Quantity:
27
Company:
Part Number:
KSZ8873MLL AM
Manufacturer:
Micrel
Quantity:
1 638
Company:
Part Number:
KSZ8873MLLJ
Manufacturer:
Micrel
Quantity:
323
Micrel, Inc.
The MII operates in either PHY mode or MAC mode. The data interface is a nibble wide and runs at ¼ the network bit rate
(not encoded). Additional signals on the transmit side indicate when data is valid or when an error occurs during
transmission. Similarly, the receive side has signals that convey when the data is valid and without physical layer errors.
For half duplex operation, the SCOL signal indicates if a collision has occurred during transmission.
The KSZ8873MLL/FLL does not provide the MRXER signal for PHY mode operation and the MTXER signal for MAC
mode operation. Normally, MRXER indicates a receive error coming from the physical layer device and MTXER indicates
a transmit error from the MAC device. Since the switch filters error frames, these MII error signals are not used by the
KSZ8873MLL/FLL. So, for PHY mode operation, if the device interfacing with the KSZ8873MLL/FLL has an MRXER input
pin, it needs to be tied low. And, for MAC mode operation, if the device interfacing with the KSZ8873MLL/FLL has an
MTXER input pin, it also needs to be tied low.
The KSZ8873MLL/FLL provides a bypass feature in the MII PHY mode. Pin SMTXER3/MII_LINK is used for MII link
status. If the host is power down, pin MII_LINK will go to high. In this case, no new ingress frames from port1 or port 2 will
be sent out through port 3, and the frames for port 3 already in packet memory will be flushed out.
RMII Interface Operation
The Reduced Media Independent Interface (RMII) specifies a low pin count Media Independent Interface (MII). RMII
provides a common interface between physical layer and MAC layer devices, and has the following key characteristics:
1. ports 10Mbps and 100Mbps data rates.
2. Uses a single 50 MHz clock reference (provided internally or externally).
3. Provides independent 2-bit wide (di-bit) transmit and receive data paths.
4. Contains two distinct groups of signals: one for transmission and the other for reception
When EN_REFCLKO_3 is high, KSZ8873RLL will output a 50MHz in REFCLKO_3. Register 198 bit[3] is used to select
internal or external reference clock. Internal reference clock means that the clock for the RMII of KSZ8873RLL will be
provided by the KSZ8873RLL internally and the REFCLKI_3 pin is unconnected. For the external reference clock, the
clock will provide to KSZ8873RLL via REFCLKI_3.
Note: If the reference clock is not provided by the KSZ8873RLL, this 50MHz reference clock has to be used in X1 pin
instead of the 25MHz crystal since the clock skew of these two clock sources will impact on the RMII timing. The SPIQ
clock selection strapping option pin is connected to low to select the 50MHz input.
The RMII provided by the KSZ8873RLL is connected to the device’s third MAC. It complies with the RMII Specification.
The following table describes the signals used by the RMII bus. Refer to RMII Specification for full detail on the signal
description.
September 2010
Reg198[3]
0
0
1
1
EN_REFCLKO_3
0
1
1
0
Table 5. RMII Clock Setting
Clock Source
External 50MHz OSC
input to REFCLKI_3
REFCLKO_3 Output Is
Feedback to
REFCLKI_3
Internal Clock Source
REFCLKI_3 is
unconnected
29
Note
EN_REFCLKO_3 = 0
to Disable
REFCLKO_3 for better
EMI
EN_REFCLKO_3 = 1
to Enable
REFCLKO_3
EN_REFCLKO_3 = 1
to Enable
REFCLKO_3
Not suggest
KSZ8873MLL/FLL/RLL
M9999-092309-1.2