LAN9311-NU SMSC, LAN9311-NU Datasheet - Page 290

• Manufacturer Part Number: LAN9311-NU
• Description: IC ETHER SW 2PRT 16BIT 128-VTQFP
• Manufacturer: SMSC
• Type: Two Port Managed Ethernet Switchr

Specifications of LAN9311-NU

• Controller Type: Ethernet Switch Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• For Use With: 638-1076 - EVALUATION BOARD LAN9311-NU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1075

Revision 1.7 (06-29-10)
BITS
6:0
9
8
7
Restart Auto-Negotiation (PHY_RST_AN)
When set, this bit restarts the Auto-Negotiation process.
0: Normal operation
1: Auto-Negotiation restarted
Duplex Mode (PHY_DUPLEX)
This bit is used to set the duplex when the
is disabled.
0: Half Duplex
1: Full Duplex
Collision Test Mode (PHY_COL_TEST)
This bit enables/disables the collision test mode of the Port x PHY. When
set, the collision signal is active during transmission. It is recommended that
this feature be used only in loopback mode.
0: Collision test mode disabled
1: Collision test mode enabled
RESERVED
Note 14.49 The default value of this bit is determined by the logical OR of the Auto-Negotiation strap
Note 14.50 The default value of this bit is determined by the value of the Auto-Negotiation strap
Note 14.51 The default value of this bit is determined by the logical AND of the negation of the Auto-
(autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY) and the speed select
strap (speed_strap_1 for Port 1 PHY, speed_strap_2 for Port 2 PHY). Essentially, if the
Auto-Negotiation strap is set, the default value is 1, otherwise the default is determined by
the value of the speed select strap. Refer to
page 40
(autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY). Refer to
"Configuration Straps," on page 40
Negotiation strap (autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY) and
the duplex select strap (duplex_strap_1 for Port 1 PHY, duplex_strap_2 for Port 2 PHY).
Essentially, if the Auto-Negotiation strap is set, the default value is 0, otherwise the default
is determined by the value of the duplex select strap. Refer to
Straps," on page 40
for more information.
DESCRIPTION
for more information.
DATASHEET
Auto-Negotiation (PHY_AN)
290
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
for more information.
Section 4.2.4, "Configuration Straps," on
bit
Section 4.2.4, "Configuration
TYPE
R/W
R/W
R/W
SMSC LAN9311/LAN9311i
RO
SC
Section 4.2.4,
Note 14.51
DEFAULT
Datasheet
0b
0b
-