ISP1160BD01TM ST-Ericsson Inc, ISP1160BD01TM Datasheet - Page 7

• Manufacturer Part Number: ISP1160BD01TM
• Description: IC USB HOST CTRL FULL-SPD 64LQFP
• Manufacturer: ST-Ericsson Inc

Specifications of ISP1160BD01TM

• Controller Type: USB 2.0 Controller
• Interface: Parallel
• Voltage - Supply: 3.3V, 5V
• Current - Supply: 47mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-1878-2; ISP1160BD/01,118; ISP1160BD01-T

Philips Semiconductors
9397 750 13963
Product data
Table 2:
Symbol
n.c.
DACK_N
TEST_HIGH
INT
n.c.
n.c.
RESET_N
NDP_SEL
EOT
DGND
n.c.
TEST_LOW
n.c.
TEST_LOW
H_WAKEUP
n.c.
H_SUSPEND
XTAL1
XTAL2
DGND
H_PSW1_N
[1]
Pin description LQFP64
Pin
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Rev. 05 — 24 December 2004
Type
-
I
-
O
-
O
I
I
I
-
-
-
-
-
I
-
O
I
O
-
O
Description
no connection; leave this pin open
HC DMA acknowledge input; when not in use, this pin must
be connected to V
this pin must be connected to V
resistor
HC interrupt output; programmable level, edge triggered
and polarity; see
no connection; leave this pin open
no connection; leave this pin open
reset input (Schmitt trigger); a LOW level produces an
asynchronous reset (internal pull-up resistor)
indicates to the HC software the Number of Downstream
Ports (NDP) present:
0 — select 1 downstream port
1 — select 2 downstream ports
only changes the value of the NDP field in the
HcRhDescriptorA register; both ports will always be
enabled; see
(internal pull-up resistor)
DMA master device to inform the ISP1160 of end of DMA
transfer; active level is programmable; when not in use, this
pin must be connected to V
resistor; see
digital ground
no connection; leave this pin open
this pin must be connected to DGND via an external 10 k
resistor
no connection; leave this pin open
this pin must be connected to DGND via a 1 M resistor
HC wake-up input; generates a remote wake-up from the
suspend state (active HIGH); when not in use, this pin must
be connected to DGND via an external 10 k resistor
(internal pull-down resistor)
no connection; leave this pin open
HC suspend state indicator output; active HIGH
crystal input; connected directly to a 6 MHz crystal; when
this pin is connected to an external clock source,
pin XTAL2 must be left open
crystal output; connected directly to a 6 MHz crystal; when
pin XTAL1 is connected to an external clock source, this
pin must be left open
digital ground
power switching control output for downstream port 1;
open-drain output
…continued
Section 10.4.1
Section 10.3.1
Section 10.4.1
CC
via an external 10 k resistor
Embedded USB Host Controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
CC
via an external 10 k
CC
via an external 10 k
ISP1160
6 of 88