PIC18F452-I/L Microchip Technology Inc., PIC18F452-I/L Datasheet - Page 122

• Manufacturer Part Number: PIC18F452-I/L
• Description: 44 PIN, 32 KB FLASH, 1536 RAM, 34 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F452-I/L

• A/d Inputs: 8-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 36
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin PLCC
• Programmable Memory: 32K Bytes
• Ram Size: 1.5K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18FXX2
14.4
In Compare mode, the 16-bit CCPR1 (CCPR2) register
value is constantly compared against either the TMR1
register pair value, or the TMR3 register pair value.
When a match occurs, the RC2/CCP1 (RC1/CCP2) pin
is:
• driven High
• driven Low
• toggle output (High to Low or Low to High)
• remains unchanged
The action on the pin is based on the value of control
bits CCP1M3:CCP1M0 (CCP2M3:CCP2M0). At the
same time, interrupt flag bit CCP1IF (CCP2IF) is set.
14.4.1
The user must configure the CCPx pin as an output by
clearing the appropriate TRISC bit.
FIGURE 14-2:
DS39564C-page 120
Note:
RC2/CCP1 pin
RC1/CCP2 pin
Special Event Trigger will:
Compare Mode
Clearing the CCP1CON register will force
the RC2/CCP1 compare output latch to the
default low level. This is not the PORTC
I/O data latch.
Reset Timer1 or Timer3, but not set Timer1 or Timer3 interrupt flag bit,
and set bit GO/DONE (ADCON0<2>)
which starts an A/D conversion (CCP2 only)
CCP PIN CONFIGURATION
Output Enable
Output Enable
TRISC<2>
TRISC<1>
COMPARE MODE OPERATION BLOCK DIAGRAM
Q
Q
R
R
S
S
Special Event Trigger
Special Event Trigger
CCP1CON<3:0>
CCP2CON<3:0>
Mode Select
Mode Select
Output
Output
Logic
Logic
Set Flag bit CCP1IF
Set Flag bit CCP2IF
Match
Match
14.4.2
Timer1 and/or Timer3 must be running in Timer mode
or Synchronized Counter mode if the CCP module is
using the compare feature. In Asynchronous Counter
mode, the compare operation may not work.
14.4.3
When generate software interrupt is chosen, the CCP1
pin is not affected. Only a CCP interrupt is generated (if
enabled).
14.4.4
In this mode, an internal hardware trigger is generated,
which may be used to initiate an action.
The special event trigger output of CCP1 resets the
TMR1 register pair. This allows the CCPR1 register to
effectively be a 16-bit programmable period register for
Timer1.
The special trigger output of CCPx resets either the
TMR1 or TMR3 register pair. Additionally, the CCP2
Special Event Trigger will start an A/D conversion if the
A/D module is enabled.
Note:
T3CCP1
T3CCP2
TMR1H
The special event trigger from the CCP2
module will not set the Timer1 or Timer3
interrupt flag bits.
TIMER1/TIMER3 MODE SELECTION
SOFTWARE INTERRUPT MODE
SPECIAL EVENT TRIGGER
T3CCP2
TMR1L
CCPR1H CCPR1L
CCPR2H CCPR2L
Comparator
Comparator
© 2006 Microchip Technology Inc.
0
0
1
1
TMR3H
TMR3L