PIC12F683-I/MD Microchip Technology Inc., PIC12F683-I/MD Datasheet - Page 45

• Manufacturer Part Number: PIC12F683-I/MD
• Description: 8 PIN, 3.5KB FLASH, 128 RAM, 6 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC12F683-I/MD

• A/d Inputs: 4-Channel, 10-Bit
• Comparators: 1
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Frequency: 20 MHz
• Input Output: 6
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 8-Pin PDIP
• Programmable Memory: 3.5K Bytes
• Ram Size: 128 Bytes
• Serial Interface: None
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

REGISTER 6-1:
 2004 Microchip Technology Inc.
bit 7
bit 6
bit 5-4
bit 3
bit 2
bit 1
bit 0
T1CON – TIMER1 CONTROL REGISTER (ADDRESS: 10h)
bit 7
T1GINV: Timer1 Gate Invert bit
1 = Timer1 gate is inverted
0 = Timer1 gate is not inverted
TMR1GE: Timer1 Gate Enable bit
If TMR1ON = 0:
This bit is ignored.
If TMR1ON = 1:
1 = Timer1 is on if Timer1 gate is not active
0 = Timer1 is on
T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale Value
10 = 1:4 Prescale Value
01 = 1:2 Prescale Value
00 = 1:1 Prescale Value
T1OSCEN: LP Oscillator Enable Control bit
If INTOSC without CLKOUT oscillator is active:
1 = LP oscillator is enabled for Timer1 clock
0 = LP oscillator is off
Else:
This bit is ignored.
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock.
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from T1CKI pin (on the rising edge)
0 = Internal clock (F
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
Legend:
R = Readable bit
- n = Value at POR
T1GINV
R/W-0
Note 1: T1GINV bit inverts the Timer1 gate logic, regardless of source.
2: TMR1GE bit must be set to use either T1G pin or COUT, as selected by the T1GSS
TMR1GE T1CKPS1 T1CKPS0 T1OSCEN
bit (CMCON1<1>), as a Timer1 gate source.
R/W-0
OSC
/4)
R/W-0
Preliminary
W = Writable bit
‘1’ = Bit is set
(1)
(2)
R/W-0
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
T1SYNC
R/W-0
PIC12F683
TMR1CS
x = Bit is unknown
R/W-0
DS41211B-page 43
TMR1ON
R/W-0
bit 0