MCIMX536AVV8C Freescale Semiconductor, MCIMX536AVV8C Datasheet - Page 32

• Manufacturer Part Number: MCIMX536AVV8C
• Description: IC, 32-BIT MPU, 800 MHz, 529-BGA
• Manufacturer: Freescale Semiconductor
• Series: ARM Cortex-A8r

Specifications of MCIMX536AVV8C

• Core Size: 32bit
• Program Memory Size: 288KB
• Cpu Speed: 800MHz
• Digital Ic Case Style: BGA
• No. Of Pins: 529
• Supply Voltage Range: 0.8V To 1.15V
• Lead Free Status / Rohs Status: Supplier Unconfirmed

3
4
Electrical Characteristics
4.3.3
The parameters in
The LVIO pads operate only as inputs.
1
2
3
4
32
High-Level DC input voltage
Low-Level DC input voltage
Input Hysteresis
Schmitt trigger VT+
Schmitt trigger VT–
Input current (no pull-up/down)
Input current (22 kΩ Pull-up)
Input current (47 kΩ Pull-up)
Input current (100 kΩ Pull-up)
Input current (100 kΩ Pull-down)
Keeper Circuit Resistance
The single-ended signals need to be within the respective limits (Vih(dc) max, Vil(dc) min) for single-ended signals as well as
the limitations for overshoot and undershoot.
Use an off-chip pull resistor of less than 60kΩ to override this keeper.
DC Electrical Characteristics
Overshoot and undershoot conditions (transitions above OVDD and below GND) on switching pads must be held below 0.6 V,
and the duration of the overshoot/undershoot must not exceed 10% of the system clock cycle. Overshoot/undershoot must be
controlled through printed circuit board layout, transmission line impedance matching, signal line termination, or other
methods. Non-compliance to this specification may affect device reliability or cause permanent damage to the device.
To maintain a valid level, the transition edge of the input must sustain a constant slew rate (monotonic) from the current DC
level through to the target DC level, VIL or VIH. Monotonic input transition time is from 0.1 ns to 1 s. VIL and VIH do not apply
when hysteresis is enabled.
Hysteresis of 350 mV is guaranteed over all operating conditions when hysteresis is enabled.
Use an off-chip pull resistor of less than 60kΩ to override this keeper.
Low Voltage I/O (LVIO) DC Parameters
2, 3
2, 3
Table 14
i.MX53xA Automotive and Infotainment Applications Processors, Rev. 1
1, 2
1, 2
are guaranteed per the operating ranges in
Table 14. LVIO DC Electrical Characteristics
Symbol
VHYS
VT+
VT–
VIH
VIL
IIN
IIN
IIN
IIN
IIN
—
Test Conditions
OVDD = 1.875 V
OVDD = 2.775 V
OVDD = 1.875 V
OVDD = 2.775 V
VI = OVDD
VI = OVDD
VI = OVDD
VI = OVDD
VI = OVDD
VI = 0 V
VI = 0 V
VI = 0 V
VI = 0 V
VI = 0 V
—
—
—
—
0.7 × OVDD
0.5 × OVDD
0.35
Min
Table
—
—
—
—
—
—
—
—
0
6, unless otherwise noted.
125
0.62
1.27
Typ
125
1.7
—
—
—
—
—
—
—
—
4
Freescale Semiconductor
0.3 × OVDD
0.5 × OVDD
OVDD
Max
0.12
0.12
0.12
0.25
250
120
161
76
36
36
—
—
—
—
Unit
nA
μA
μA
μA
μA
kΩ
V
V
V
V
V