AMIS49587C5871RG ON Semiconductor, AMIS49587C5871RG Datasheet - Page 49

• Manufacturer Part Number: AMIS49587C5871RG
• Description: IC MODEM PLC 50/60MHZ 28PLCC
• Manufacturer: ON Semiconductor

Specifications of AMIS49587C5871RG

• Baud Rates: Selectable
• Interface: SCI
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 28-PLCC
• Number Of Transmitters: 1
• Power Supply Requirement: Single
• Package Type: PLCC
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 28
• Operating Temperature (max): 70C
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Format: -
• Lead Free Status / Rohs Status: Compliant

WriteConfigNew_Request for Slave Mode
Table 40. DESCRIPTION OF WRITECONFIGNEW_REQUEST IN SLAVE MODE
First Initiator MAC Address (FIMA)
Last Initiator MAC Address (LIMA)
Local MAC Address
Active Initiator Address
Time−out−synchro−confirm
Time−out−frame−not−ok
Time−out−not−addressed
Mac−group−addresses
Fs
Fm
R_ZC_ADJUST
NbAlarm
R_ALC_CTRL→Value
Max_Transmistting_Gain→Value
R_ALC_CTRL→Value
Max_Transmistting_Gain→Mode
R_CONF_TX_DATA_PRE_SLOT_SEL
Pad
R_CONF→MODE
R_CONF→BAUDRATE
R_CONF→MAINS_FREQ
Pad
Search method
SINC Filter
SYNCHRO−Type→Mode
SYNCHRO−Bit→Value
SYNCHRO−Bit→Mode
SearchInitiatorGain or
Min−ReceivingGain Mode
Search Initiator Gain or
Min−Receiving Gain
Max−Receiving−Gain→Value
Field
(b7 to b4)
(b3 to b1)
(b5 to b3)
(b3 to b1)
(b6 to b4)
1 bit (b0)
1 bit (b7)
1 bit (b6)
1 bit (b7)
1 bit (b5)
1 bit (b4)
1 bit (b0)
1 bit (b7)
(b3to b1)
10 bytes
Length
(b6, b5)
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
(b2,b1)
1 byte
4 bits
3 bits
3 bits
2 bits
2 bits
3 bits
3 bits
3 bits
1 bit
(b0)
http://onsemi.com
FIMA to LIMA
0000 to FFFF
0000 to FFFF
0000 to FFFF
0000 to FFFF
0000 to FFFF
0001 to 0FFF
0001 to 0FFF
0000 to 0FFF
(FIMA−1)
00 to FF
0FFE or
0001 to
Value
XXXX
0000
0000
XXX
XXX
XXX
XXX
010
00
01
10
11
0
1
0
1
0
0
1
0
0
1
0
1
0
1
0
49
First value for Initiator MAC address
Last value for Initiator MAC address
Slave Mode: New
Slave (Registered)
Slave (unlocked)
Slave (locked on an initiator)
In seconds.
In seconds
In minutes (Not used in Master & Monitor mode)
5 MAC group addresses (Not used in Master mode)
Step Register for the Space Frequency Fs
Step Register for the Mark Frequency Fm
Value according to the voltage level of the 50 Hz
information for the input of the PLL.
Number of repetitions of a Phy Alarm
Disable Phy Alarm functionality
Attenuation value in fixed mode
Automatic level control
Fixed mode
The output pin is the PRE_SLOT signal or Mode = Master
The output pin is the transmitted DATA (for.Radio)
This bit is not used (adjust length at 1 byte)
Slave mode for server station
300 baud @ 50 Hz or 360 baud @ 60 Hz
600 baud @ 50 Hz or 720 baud @ 60 Hz
1200 baud @ 50 Hz or 1440 baud @ 60 Hz
2400 baud @ 50 Hz or 2880 baud @ 60 Hz
mains frequency = 50 Hz
mains frequency = 60 Hz
This bit is not used (adjust length at 1 byte)
Method V6
Method V3
Disabled (1111)
Enabled (1331)
Must be set to 0 (Synchronization on sub−frame
preamble)
Synchro−bit value (in chip clock) in fixed mode
Must be set to 1 (Fixed synchro bit)
0 Search Initiator Gain selected
1 Min Receiving Gain selected
Value of the gain for Intelligent Synchronisation
or Min Receiving Value
Min Gain of reception = (value * 6 db)
Max Receiving gain value in limited mode
Range of reception = (value * 6 db)
Description