AMIS49587C5871RG ON Semiconductor, AMIS49587C5871RG Datasheet - Page 51

• Manufacturer Part Number: AMIS49587C5871RG
• Description: IC MODEM PLC 50/60MHZ 28PLCC
• Manufacturer: ON Semiconductor

Specifications of AMIS49587C5871RG

• Baud Rates: Selectable
• Interface: SCI
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 28-PLCC
• Number Of Transmitters: 1
• Power Supply Requirement: Single
• Package Type: PLCC
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 28
• Operating Temperature (max): 70C
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Format: -
• Lead Free Status / Rohs Status: Compliant

Table 41. DESCRIPTION OF WRITECONFIGNEW_REQUEST IN MONITOR MODE
R_CONF→BAUDRATE
R_CONF→MAINS_FREQ
Pad
Search method
SINC Filter
SYNCHRO−Type→Mode
SYNCHRO−Bit→Value
SYNCHRO−Bit→Mode
SearchInitiatorGain or
Min−ReceivingGain Mode
Search Initiator Gain or
Min−Receiving Gain
Max−Receiving−Gain→Value
Max−Receiving−Gain→Mode
Time out Inter Character TIC
Bad CRC transmitting
Pad correcting
FSK +
Alarm Filter
Synchro without Gain Min
Repeater
Time−out−search−initiator
Field
(b3 to b1)
(b6 to b4)
1 bit (b7)
1 bit (b5)
1 bit (b4)
1 bit (b0)
1 bit (b7)
(b3to b1)
1 bit (b0)
1 bit (b7)
1 bit (b6)
1 bit (b5)
1 bit (b4)
1 bit (b3)
1 bit (b2)
Length
(b6, b5)
(b2,b1)
(b1,b0)
2 bytes
2 bits
2 bits
3 bits
3 bits
3 bits
2 bits
1 bit
(b0)
http://onsemi.com
XXXX
Value
XXX
XXX
XXX
XX
00
01
10
11
0
1
0
0
1
0
1
0
1
1
0
1
0
1
X
X
0
1
X
x
51
300 baud @ 50 Hz or 360 baud @ 60 Hz
600 baud @ 50 Hz or 720 baud @ 60 Hz
1200 baud @ 50 Hz or 1440 baud @ 60 Hz
2400 baud @ 50 Hz or 2880 baud @ 60 Hz
mains frequency = 50 Hz
mains frequency = 60 Hz
This bit is not used (adjust length at 1 byte)
Method V6
Method V3
Disabled (1111)
Enabled (1331)
Must be set to 0 (Synchronization on sub−frame pre-
amble)
Synchro−bit value (in chip clock) in fixed mode
Must be set to 1 (Fixed synchro bit)
1 Min Receiving Gain selected
Value of the gain for Intelligent Synchronisation
or Min Receiving Value
Min Gain of reception = (value * 6 db)
Max Receiving gain value in limited mode
Range of reception = (value * 6 db)
Non limited Max−Receiving−Gain
Limited Max−Receiving−Gain
Constant of 10 ms
5 characters depending on communication speed
Don’t care
Don’t care
Disables the improvement of FSK
Enables the improvement of FSK
Don’t care
0 disabled
1 enabled
Don’t care
Don’t care
Description