CC-W9M-NA37-XE Digi International, CC-W9M-NA37-XE Datasheet - Page 62
CC-W9M-NA37-XE
Manufacturer Part Number
CC-W9M-NA37-XE
Description
MOD WI-9M 64MB SDRAM 128MB FLASH
Manufacturer
Digi International
Series
-r
Datasheet
1.CC-W9M-NA37-XE.pdf
(145 pages)
Specifications of CC-W9M-NA37-XE
Module/board Type
Core Module
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
Networking
- Current page: 62 of 145
- Download datasheet (8Mb)
www.digiembedded.com
U s e r i n t e r f a c e
Power
management
G e n e r a l i n f o r m a t i o n
Power supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The ConnectCore 9M 2443 development board implements two user buttons and two
user LEDs in addition to those provided on the module. The user LEDs on the
development board can be enabled or disabled by correctly setting jumper J5 and
J6. The table below shows which S3C22443 GPIO is available for implementing the
user interface.
Both push-buttons can also be used for wake-up functions.
User buttons can also be used as a wake-up event for power management modes.
The user LEDs on the development board can be enabled or disabled by correctly
setting J5/J6.
The integrated on-chip functions of the module are outlined below.
Signal name
USER_BUTTON1
USER_LED1#
USER_BUTTON2
USER_LED2#
Signal name
USER_LED_1
USER_LED_2
ConnectCore 9M 2443 Development Board is powered by either the main 9-
30VDC power supply or by the PoE (IEEE 802.3af) module near to the Ethernet
connector.
Both power supply sources can be switched off through one power switch.
From the varying input voltage (9-30VDC), a stable base power supply is
created on the ConnectCore 9M 2443 development board. The 3.3VDC power
supply is provided to the module, where other power supplies can be
generated.
GPIO used
GPF0
GPL11
GPF1
GPL10
GPIO used
GPL11
GPL10
Comments
100 Ohm serial resistors should be used to
avoid conflicts with the CPU functions when
the buttons are pushed.
Jumper JP5 as to be set.
100 Ohm serial resistors are used to avoid
conflicts with the CPU functions when the
buttons are pushed.
Jumper JP6 as to be set.
62
Related parts for CC-W9M-NA37-XE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools ConnectCore 9C ConnectCore Wi-9C
Manufacturer:
Digi International
Part Number:
Description:
MOD WI-9M 64MB SDRAM 128MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT JUMP START WI-9M 2443 LINUX
Manufacturer:
Digi International
Part Number:
Description:
KIT JUMP START ME 9210 NET+OS 7
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT JUMP START ME 9210 LINUX
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT INTEGRATION ME MOD S MODELS
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT DEV SP ADPT NO RAVEN
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT DEV SP ADAPTER
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
DIGI CONNECT 4MB FLASH 8MB RAM
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 7U 16MB SDRAM 2MB FLASH
Manufacturer:
Digi International
Part Number:
Description:
MODULE 7U 16MB SDRAM 8MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 9P 8MB SDRAM 4MB FLASH
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 9P 16MB SDRAM 8MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 9P 32MB SDRAM 16MB FLASH
Manufacturer:
Digi International
Datasheet: