TE28F160S375 Intel, TE28F160S375 Datasheet - Page 27

• Manufacturer Part Number: TE28F160S375
• Manufacturer: Intel

Specifications of TE28F160S375

• Cell Type: NOR
• Density: 16Mb
• Access Time (max): 75ns
• Interface Type: Parallel
• Boot Type: Not Required
• Address Bus: 21/20Bit
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP
• Program/erase Volt (typ): 2.7/3.3/5V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8/16Bit
• Number Of Words: 2M/1M
• Supply Current: 30mA
• Mounting: Surface Mount
• Pin Count: 56
• Lead Free Status / Rohs Status: Not Compliant

This two-step command sequence of setup followed
by execution ensures that block contents are not
accidentally erased. An invalid Full Chip Erase
command sequence will result in both Status
Register bits SR.4 and SR.5 being set to 1. Also,
reliable full chip erasure can only occur when
V
these voltages, block contents are protected
against erasure. If full chip erase is attempted while
V
WP# = V
chip erase cannot be suspended.
4.8
To program the flash device via the write buffers, a
Write to Buffer command sequence is initiated. A
variable number of bytes or words, up to the buffer
size, can be written into the buffer and programmed
to the flash device. First, the Write to Buffer setup
command is issued along with the Block Address.
At this point, the eXtended Status Register
information is loaded and XSR.7 reverts to the
“buffer available” status. If XSR.7 = 0, no write
buffer is available. To retry, continue monitoring
XSR.7 by issuing the Write to Buffer setup
command with the Block Address until XSR.7 = 1.
When XSR.7 transitions to a “1,” the buffer is ready
for loading.
Now a Word/Byte count is issued at an address
within the block. On the next write, a device start
address is given along with the write buffer data.
For maximum programming performance and lower
power, align the start address at the beginning of a
Write Buffer boundary. Subsequent writes must
supply additional device addresses and data,
depending on the count. All subsequent addresses
must lie within the start address plus the count.
After the final buffer data is given, a Write Confirm
command is issued. This initiates the WSM to begin
copying the buffer data to the flash memory. If a
command other than Write Confirm is written to the
device, an “Invalid Command/Sequence” error will
be generated and Status Register bits SR.5 and
SR.4 will be set to “1.” For additional buffer writes,
issue another Write to Buffer setup command and
check XSR.7. The write buffers can be loaded while
the WSM is busy as long as XSR.7 indicates that a
buffer is available. Refer to Figure 7 for the Write to
Buffer flowchart.
CC
PP
ADVANCE INFORMATION
= V
V
PPLK
CC1/2
Write to Buffer Command
IL
, only unlocked blocks are erased. Full
, SR.3 and SR.5 will be set to 1. When
and V
PP
= V
PPH1/2
. In the absence of
If an error occurs while writing, the device will stop
programming, and Status Register bit SR.4 will be
set to a “1” to indicate a program failure. Any time a
media failure occurs during a program or an erase
(SR.4 or SR.5 is set), the device will not accept any
more Write to Buffer commands. Additionally, if the
user attempts to write past an erase block boundary
with a Write to Buffer command, the device will
abort programming. This will generate an “Invalid
Command/Sequence” error and Status Register bits
SR.5 and SR.4 will be set to “1.” To clear SR.4
and/or SR.5, issue a Clear Status Register
command.
Reliable buffered programming can only occur
when V
programming is attempted while V
Status Register bits SR.4 and SR.5 will be set to
“1.” Programming attempts with invalid V
voltages produce spurious results and should not
be attempted. Finally, successful programming
requires that the corresponding Block Lock-Bit be
cleared, or WP# = V
attempted when the corresponding Block Lock-Bit
is set and WP# = V
“1.”
4.9
Byte/Word programming is executed by a two-cycle
command sequence. Byte/Word Program setup
(standard 40H or alternate 10H) is written, followed
by a second write that specifies the address and
data (latched on the rising edge of WE#). The WSM
then takes over, controlling the program and verify
algorithms internally. After the write sequence is
written, the device automatically outputs Status
Register data when read. The CPU can detect the
completion of the program event by analyzing STS
in level RY/BY# mode or Status Register bit SR.7.
When programming is complete, Status Register bit
SR.4 should be checked. If a programming error is
detected, the Status Register should be cleared.
The internal WSM verify only detects errors for “1”s
that do not successfully program to “0”s. The CUI
remains in read Status Register mode until it
receives another command. Refer to Figure 8 for
the Word/Byte Program flowchart.
Also, Reliable byte/word programming can only
occur when V
absence of this high voltage, contents are protected
against programming. If a byte/word program is
CC
Byte/Word Program Commands
= V
CC
= V
CC1/2
IL
CC1/2
, SR.1 and SR.4 will be set to
IH
and V
. If a buffered write is
and V
28F160S3, 28F320S3
PP
PP
= V
= V
PP
PPH1/2
CC
PPH1/2
and V
. In the
V
PPLK
. If
27
PP
,