PIC16LF1933-E/MV Microchip Technology, PIC16LF1933-E/MV Datasheet - Page 128

• Manufacturer Part Number: PIC16LF1933-E/MV
• Description: IC MCU 8BIT 7KB FLASH 28UQFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF1933-E/MV

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-UFQFN Exposed Pad
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16(L)F1933
12.4
PORTC is a 8-bit wide, bidirectional port. The
corresponding
(Register
corresponding PORTC pin an input (i.e., put the
corresponding output driver in a High-Impedance mode).
Clearing a TRISC bit (= 0) will make the corresponding
PORTC pin an output (i.e., enable the output driver and
put the contents of the output latch on the selected pin).
Example 12-1
Reading the PORTC register
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then written
to the PORT data latch (LATC).
The TRISC register
PORTC pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits in
the TRISC register are maintained set when using them
as analog inputs. I/O pins configured as analog input
always read ‘0’.
DS41575A-page 128
PORTC Registers
12-12). Setting a TRISC bit (= 1) will make the
shows how to initialize an I/O port.
data
direction
(Register
(Register
12-12) controls the
register
12-11) reads the
is
TRISC
Preliminary
12.4.1
Each PORTC pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are shown in
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the lowest number in
the following lists.
Analog input and some digital input functions are not
included in the list below. These input functions can
remain active when the pin is configured as an output.
Certain digital input functions override other port
functions and are included in
TABLE 12-7:
Note 1:
Pin Name
RC0
RC1
RC2
RC3
RC4
RC5
RC6
RC7
Priority listed from highest to lowest.
PORTC FUNCTIONS AND OUTPUT
PRIORITIES
Table
PORTC OUTPUT PRIORITY
T1OSO (Timer1 Oscillator)
CCP2/P2B
RC0
T1OSI (Timer1 Oscillator)
CCP2/P2A
RC1
SEG3 (LCD)
CCP1/P1A
RC2
SEG6 (LCD)
SCL (MSSP)
SCK (MSSP)
RC3
SEG11 (LCD)
SDA (MSSP)
RC4
SEG10 (LCD)
SDO (MSSP)
RC5
ISEG9 (LCD)
TX (EUSART)
CK (EUSART)
CCP3/P3A, 28-pin only
RC6
SEG8 (LCD)
DT (EUSART)
CCP3/P3B, 28 pin only
RC7
12-7.
 2011 Microchip Technology Inc.
Function Priority
Table
12-7.
(1)