AT32UC3A4128S Atmel Corporation, AT32UC3A4128S Datasheet - Page 117

• Manufacturer Part Number: AT32UC3A4128S
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A4128S

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: AES
• Sram (kbytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

9.4
9.4.1
32002F–03/2010
Breakpoints
Overview
dard. This includes enabling the AUX port, and controlling the speed of the clock and data
compared to the CPU clock.
Table 9-22.
The Nexus Recommended Register map supports up to 8 universal breakpoints. However since
the AVR32UC hardware employs separate instruction and data memories, the OCD system
must also separate program and data breakpoints. Any breakpoint can also be programmed as
R/W
R
R/W
R
R
R/W
R/W
R/W
R/W
R
R/W
Bit Number
31:16
15:14
13
12
11
10
9
8
7:4
3:0
AUX Port Control Register
Field Name
Reserved
AXS
Reserved
Reserved
LS
DDR
AXO
AXE
Reserved
DIV
Init. Val.
0
0
0
0
0
0
0
0
0
0
Description
Reserved
These bits are reserved, and will always read as 0
AXS - Auxiliary Port Select
0: AUX port is mapped to pin configuration 0.
1: AUX port is mapped to pin configuration 1.
2: AUX port is mapped to pin configuration 2.
3: AUX port is mapped to pin configuration 3.
Reserved
This bit is reserved, and will always read as 0
Reserved
This bit is reserved, and will always read as 0.
LS - Low Speed
0:AUX port runs at the same speed as the CPU
1:AUX port runs at reduced speed compared to
the CPU.
DDR - Double Data Rate
Setting this bit halves the MCKO rate so that MDO
data must be sampled on both edges of MCKO.
1 = Double data rate mode
0 = Single datarate mode
AXO - Auxiliary Port Override
0: AUX port is mapped to the pins dictated by
AXS.
1: AUX port is overridden and mapped to pin
configuration 1.
AXE - Auxiliary Port Enable
0: AUX port is used for GPIO
1: AUX port is used for Nexus operation.
This bit does not need to be written in devices with
dedicated AUX pins
Reserved
These bits are reserved, and will always read as 0
DIV - Division factor
If LS=1, the DIV value selects the frame rate of the
AUX port.
AVR32
117