ATmega325P Atmel Corporation, ATmega325P Datasheet - Page 55

• Manufacturer Part Number: ATmega325P
• Manufacturer: Atmel Corporation

Specifications of ATmega325P

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8023F–AVR–07/09
When the BOOTRST Fuse is unprogrammed, the Boot section size set to 4K bytes and the
IVSEL bit in the MCUCR Register is set before any interrupts are enabled, the most typical and
general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed and the Boot section size set to 4K bytes, the most
typical and general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed, the Boot section size set to 4K bytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses is:
0x0032
0x0033
0x0034
0x0035
0x0036
0x0037
Address Labels Code
0x0000
0x0001
0x0002
0x0003
0x0004
0x0005
;
.org 0x3802/0x7802
0x3804/0x7804
0x3806/0x7806
...
0x1C2C
Address Labels Code
.org 0x0002
0x0002
0x0004
...
0x002C
;
.org 0x3800/0x7800
0x3800/0x7801RESET:ldir16,high(RAMEND); Main program start
0x3801/0x7801
0x3802/0x7802
0x3803/0x7803
0x3804/0x7804
0x3805/0x7805
RESET: ldi
RESET:
...
out
ldi
out
sei
<instr> xxx
jmp
jmp
...
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
ldi
out
ldi
out
sei
<inst
r>
...
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
EXT_INT0
PCINT0
...
SPM_RDY
EXT_INT0
PCINT0
...
SPM_RDY
SPH,r16
r16,low(RAMEND)
SPL,r16
xxx
r16, high(RAMEND)
SPH,r16
r16, low(RAMEND)
SPL,r16
xxx
...
Comments
; Set Stack Pointer to top of RAM
Comments
; Set Stack Pointer to top of RAM
; Enable interrupts
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; Enable interrupts
ATmega325P/3250P
; Main program start
; Set Stack Pointer to top of RAM
; Enable interrupts
55