ATmega649 Atmel Corporation, ATmega649 Datasheet - Page 324
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega649
Manufacturer Part Number
ATmega649
Description
Manufacturer
Atmel Corporation
Specifications of ATmega649
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
54
Ext Interrupts
17
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
100
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega649-16AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega649-16MU
Manufacturer:
Atmel
Quantity:
135
Part Number:
ATmega6490-16AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega6490-16AU
Manufacturer:
Atmel
Quantity:
135
Company:
Part Number:
ATmega6490-16AUR
Manufacturer:
Atmel
Quantity:
1 500
Company:
Part Number:
ATmega6490A-AU
Manufacturer:
Atmel
Quantity:
1 250
Company:
Part Number:
ATmega6490A-AUR
Manufacturer:
Maxim
Quantity:
43
27.8.18
27.8.19
27.8.20
324
ATmega329/3290/649/6490
Programming the EEPROM
Reading the EEPROM
Programming the Fuses
3. Load the page address using programming instructions 3b and 3c. PCWORD (refer to
4. Enter JTAG instruction PROG_PAGEREAD.
5. Read the entire page (or Flash) by shifting out all instruction words in the page (or Flash),
6. Enter JTAG instruction PROG_COMMANDS.
7. Repeat steps 3 to 6 until all data have been read.
Before programming the EEPROM a Chip Erase must be performed, see “Performing Chip
Erase” on page 323.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable EEPROM write using programming instruction 4a.
3. Load address High byte using programming instruction 4b.
4. Load address Low byte using programming instruction 4c.
5. Load data using programming instructions 4d and 4e.
6. Repeat steps 4 and 5 for all data bytes in the page.
7. Write the data using programming instruction 4f.
8. Poll for EEPROM write complete using programming instruction 4g, or wait for t
9. Repeat steps 3 to 8 until all data have been programmed.
Note that the PROG_PAGELOAD instruction can not be used when programming the EEPROM.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable EEPROM read using programming instruction 5a.
3. Load address using programming instructions 5b and 5c.
4. Read data using programming instruction 5d.
5. Repeat steps 3 and 4 until all data have been read.
Note that the PROG_PAGEREAD instruction can not be used when reading the EEPROM.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Fuse write using programming instruction 6a.
3. Load data high byte using programming instructions 6b. A bit value of “0” will program the
4. Write Fuse High byte using programming instruction 6c.
5. Poll for Fuse write complete using programming instruction 6d, or wait for t
6. Load data low byte using programming instructions 6e. A “0” will program the fuse, a “1”
7. Write Fuse low byte using programming instruction 6f.
Table 27-10 on page
starting with the LSB of the first instruction in the page (Flash) and ending with the MSB
of the last instruction in the page (Flash). The Capture-DR state both captures the data
from the Flash, and also auto-increments the program counter after each word is read.
Note that Capture-DR comes before the shift-DR state. Hence, the first byte which is
shifted out contains valid data.
(refer to
corresponding fuse, a “1” will unprogram the fuse.
Table 27-12 on page
will unprogram the fuse.
Table 27-12 on page
298) is used to address within one page and must be written as 0.
307).
307).
WLRH
2552K–AVR–04/11
(refer to
WLRH