ATmega64A Atmel Corporation, ATmega64A Datasheet - Page 291

• Manufacturer Part Number: ATmega64A
• Manufacturer: Atmel Corporation

Specifications of ATmega64A

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8160C–AVR–07/09
.equ PAGESIZEB = PAGESIZE*2
.org SMALLBOOTSTART
Write_page:
Wrloop:
Rdloop:
Return:
;-the routine must be placed inside the boot space
; (at least the Do_spm sub routine). Only code inside NRWW section can
; be read during self-programming (Page Erase and Page Write).
;-registers used: r0, r1, temp1 (r16), temp2 (r17), looplo (r24),
; loophi (r25), spmcrval (r20)
; storing and restoring of registers is not included in the routine
; register usage can be optimized at the expense of code size
;-It is assumed that either the interrupt table is moved to the Boot
; loader section or that the interrupts are disabled.
; Page Erase
ldi
call Do_spm
; re-enable the RWW section
ldi
call Do_spm
; transfer data from RAM to Flash page buffer
ldi
ldi
ld
ld
ldi
call Do_spm
adiw ZH:ZL, 2
sbiw loophi:looplo, 2
brne Wrloop
; execute Page Write
subi ZL, low(PAGESIZEB)
sbci ZH, high(PAGESIZEB)
ldi
call Do_spm
; re-enable the RWW section
ldi
call Do_spm
; read back and check, optional
ldi
ldi
subi YL, low(PAGESIZEB)
sbci YH, high(PAGESIZEB)
lpm
ld
cpse r0, r1
jmp
sbiw loophi:looplo, 1
brne Rdloop
; return to RWW section
; verify that RWW section is safe to read
lds
sbrs temp1, RWWSB
ret
; re-enable the RWW section
ldi
call Do_spm
rjmp Return
spmcrval, (1<<PGERS) | (1<<SPMEN)
spmcrval, (1<<RWWSRE) | (1<<SPMEN)
looplo, low(PAGESIZEB)
loophi, high(PAGESIZEB) ;not required for PAGESIZEB<=256
r0, Y+
r1, Y+
spmcrval, (1<<SPMEN)
spmcrval, (1<<PGWRT) | (1<<SPMEN)
spmcrval, (1<<RWWSRE) | (1<<SPMEN)
looplo, low(PAGESIZEB)
loophi, high(PAGESIZEB) ;not required for PAGESIZEB<=256
r0, Z+
r1, Y+
Error
temp1, SPMCSR
spmcrval, (1<<RWWSRE) | (1<<SPMEN)
; If RWWSB is set, the RWW section is not ready yet
;init loop variable
;use subi for PAGESIZEB<=256
;restore pointer
;not required for PAGESIZEB<=256
;init loop variable
;restore pointer
;use subi for PAGESIZEB<=256
;PAGESIZEB is page size in BYTES, not words
ATmega64A
291