ATtiny13 Atmel Corporation, ATtiny13 Datasheet - Page 104
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny13
Manufacturer Part Number
ATtiny13
Description
Manufacturer
Atmel Corporation
Specifications of ATtiny13
Flash (kbytes)
1 Kbytes
Pin Count
8
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
6
Ext Interrupts
6
Usb Speed
No
Usb Interface
No
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.06
Eeprom (bytes)
64
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
1
Output Compare Channels
2
Pwm Channels
2
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATtiny13-10SSU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny13-12SI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny13-16PI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny13-20MI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny13-20PU
Manufacturer:
NXP
Quantity:
2 000
Company:
Part Number:
ATtiny13-20PU
Manufacturer:
Atmel
Quantity:
37 287
Part Number:
ATtiny13-20SSI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny13-20SSU-SL383
Manufacturer:
ATMEL
Quantity:
4 132
Company:
Part Number:
ATtiny13A-MMU
Manufacturer:
DP
Quantity:
34 000
Company:
Part Number:
ATtiny13A-MMUR
Manufacturer:
TI
Quantity:
4 430
17.2.1
17.3
17.4
17.5
104
Calibration Bytes
Signature Bytes
Page Size
ATtiny13
Latching of Fuses
Note that fuse bits are locked if Lock Bit 1 (LB1) is programmed. Program the fuse bits before
programming the lock bits. The status of the fuse bits is not affected by Chip Erase.
Fuse bits can also be read by the device firmware. See section
from Firmware” on page
The fuse values are latched when the device enters programming mode and changes of the
fuse values will have no effect until the part leaves Programming mode. This does not apply to
the EESAVE fuse which will take effect once it is programmed. The fuses are also latched on
Power-up in Normal mode.
The signature area of the ATtiny13 contains two bytes of calibration data for the internal oscilla-
tor. The calibration data in the high byte of address 0x00 is for use with the oscillator set to 9.6
MHz operation. During reset, this byte is automatically written into the OSCCAL register to
ensure correct frequency of the oscillator.
There is a separate calibration byte for the internal oscillator in 4.8 MHz mode of operation but
this data is not loaded automatically. The hardware always loads the 9.6 MHz calibraiton data
during reset. To use separate calibration data for the oscillator in 4.8 MHz mode the OSCCAL
register must be updated by firmware. The calibration data for 4.8 MHz operation is located in
the high byte at address 0x01 of the signature area.
All Atmel microcontrollers have a three-byte signature code which identifies the device. This
code can be read in both serial and high-voltage programming mode, even when the device is
locked. The three bytes reside in a separate address space.
For the ATtiny13 the signature bytes are:
Table 17-5.
Table 17-6.
512 words (1K byte)
• 0x000: 0x1E (indicates manufactured by Atmel).
• 0x001: 0x90 (indicates 1 KB Flash memory).
• 0x002: 0x07 (indicates ATtiny13 device when 0x001 is 0x90).
EEPROM Size
Flash Size
64 bytes
No. of Words in a Page and No. of Pages in the Flash
No. of Words in a Page and No. of Pages in the EEPROM
99.
Page Size
Page Size
16 words
4 bytes
PCWORD
PCWORD
EEA[1:0]
PC[3:0]
No. of Pages
No. of Pages
16
32
“Reading Fuse and Lock Bits
PCPAGE
EEA[5:2]
PCPAGE
PC[8:4]
2535J–AVR–08/10
EEAMSB
PCMSB
5
8