ATtiny13 Atmel Corporation, ATtiny13 Datasheet - Page 119

• Manufacturer Part Number: ATtiny13
• Manufacturer: Atmel Corporation

Specifications of ATtiny13

• Flash (kbytes): 1 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.06
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

18.5
Table 18-4.
18.5.1
18.6
Table 18-6.
Note:
2535J–AVR–08/10
Symbol
V
I
t
t
LAC
APD
DPD
Symbol
AIO
V
V
V
t
t
V
HYST
BOD
t
I
RST
POT
RST
BG
BG
BG
System and Reset Characteristics
Analog Comparator Characteristics
All parameters are based on simulation results and they are not tested in production
Brown-Out Detection
Parameter
Input Offset Voltage
Input Leakage Current
Analog Propagation Delay
(from saturation to slight overdrive)
Analog Propagation Delay
(large step change)
Digital Propagation Delay
Parameter
Power-on Reset Threshold Voltage (rising)
Power-on Reset Threshold Voltage
(falling)
RESET Pin Threshold Voltage
Minimum pulse width on RESET Pin
Brown-out Detector Hysteresis
Min Pulse Width on Brown-out Reset
Bandgap reference voltage
Bandgap reference start-up time
Bandgap reference current consumption
Reset, Brown-out and Internal Voltage Reference Characteristics
Analog Comparator Characteristics, T
(1)
Note:
Table 18-5.
Note:
BODLEVEL [1:0] Fuses
1. The Power-on Reset will not work unless the supply voltage has been below V
1. V
this is the case, the device is tested down to V
antees that a Brown-out Reset will occur before V
operation of the microcontroller is no longer guaranteed.
BOT
10
01
00
11
V
BOT
may be below nominal minimum operating voltage for some devices. For devices where
vs. BODLEVEL Fuse Coding
A
= -40°C to +85°C
Condition
V
V
V
V
V
V
V
Condition
T
T
V
V
CC
CC
CC
CC
CC
CC
CC
A
A
CC
CC
= -40 to +85°C
= -40 to +85°C
= 5V, V
= 5V, V
= 2.7V
= 4.0V
= 2.7V
= 4.0V
= 1.8V - 5.5
= 1.8V - 5.5V
= 1.8V - 5.5V
Min
IN
IN
(1)
= V
= V
CC
CC
/ 2
/ 2
0.2 V
Min
1.0
Typ
CC
2
1.8
2.7
4.3
CC
= V
CC
(1)
BOD Disabled
BOT
drops to a voltage where correct
Min
-50
during the production test. This guar-
Typ
1.2
1.1
1.1
50
40
15
< 10
Typ
750
500
100
75
Max
1
(1)
0.9 V
Max
2.5
1.2
70
Max
CC
40
50
2
POT
(falling)
Units
Units
V
mV
Units
µs
µs
µs
µs
CLK
V
V
V
V
mV
nA
ns
119