ATtiny24A Atmel Corporation, ATtiny24A Datasheet - Page 64

• Manufacturer Part Number: ATtiny24A
• Manufacturer: Atmel Corporation

Specifications of ATtiny24A

• Flash (kbytes): 2 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

10.2.2
64
ATtiny24A/44A/84A
Alternate Functions of Port B
The Port B pins with alternate function are shown in
Table 10-7.
• Port B, Bit 0 – XTAL1/PCINT8
• Port B, Bit 1 – XTAL2/PCINT9
• Port B, Bit 2 – INT0/OC0A/CKOUT/PCINT10
• XTAL1: Chip Clock Oscillator pin 1. Used for all chip clock sources except internal
• PCINT8: Pin Change Interrupt source 8. The PB0 pin can serve as an external interrupt
• CLKI: Clock Input from an external clock source, see
• XTAL2: Chip Clock Oscillator pin 2. Used as clock pin for all chip clock sources except
• PCINT9: Pin Change Interrupt source 9. The PB1 pin can serve as an external interrupt
• INT0: External Interrupt Request 0.
• OC0A: Output Compare Match output: The PB2 pin can serve as an external output for the
• CKOUT - System Clock Output: The system clock can be output on the PB2 pin. The system
• PCINT10: Pin Change Interrupt source 10. The PB2 pin can serve as an external interrupt
calibrateble RC oscillator. When used as a clock pin, the pin can not be used as an I/O pin.
When using internal calibratable RC Oscillator as a chip clock source, PB0 serves as an
ordinary I/O pin.
source for pin change interrupt 1.
internal calibrateble RC Oscillator and external clock. When used as a clock pin, the pin can
not be used as an I/O pin. When using internal calibratable RC Oscillator or External clock as
a Chip clock sources, PB1 serves as an ordinary I/O pin.
source for pin change interrupt 1.
Timer/Counter0 Compare Match A. The PB2 pin has to be configured as an output (DDB2
set (one)) to serve this function. The OC0A pin is also the output pin for the PWM mode timer
function.
clock will be output if the CKOUT Fuse is programmed, regardless of the PORTB2 and DDB2
settings. It will also be output during reset.
source for pin change interrupt 1.
Port Pin
PB0
PB1
PB3
PB2
Port B Pins Alternate Functions
Alternate Function
XTAL1: Crystal Oscillator Input
PCINT8: Pin Change Interrupt 1, Source 8
CLKI:
XTAL2: Crystal Oscillator Output
PCINT9: Pin Change Interrupt 1, Source 9
INT0:
OC0A: Timer/Counter0 Compare Match A output
CKOUT: System Clock Output
PCINT10:Pin Change Interrupt 1, Source 10
RESET: Reset pin
dW:
PCINT11:Pin Change Interrupt 1, Source 11.
External Interrupt 0 Input
External Clock Input
debugWire I/O
Table
“External Clock” on page
10-7.
26.
8183D–AVR–04/11