P89LPC9321 NXP Semiconductors, P89LPC9321 Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
P89LPC9321
Manufacturer Part Number
P89LPC9321
Description
The P89LPC9321 is a single-chip microcontroller, available in low cost packages, basedon a high performance processor architecture that executes instructions in two to fourclocks, six times the rate of standard 80C51 devices
Manufacturer
NXP Semiconductors
Datasheet
1.P89LPC9321.pdf
(71 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P89LPC9321FA
Manufacturer:
NXP
Quantity:
20 000
Company:
Part Number:
P89LPC9321FA,112
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P89LPC9321FA,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P89LPC9321FDH
Manufacturer:
ON
Quantity:
36
NXP Semiconductors
P89LPC9321
Product data sheet
7.16.1.1 Quasi-bidirectional output configuration
7.16.1.2 Open-drain output configuration
7.16.1 Port configurations
7.16 I/O ports
The P89LPC9321 has four I/O ports: Port 0, Port 1, Port 2 and Port 3. Ports 0, 1, and 2
are 8-bit ports, and Port 3 is a 2-bit port. The exact number of I/O pins available depends
upon the clock and reset options chosen, as shown in
Table 7.
All but three I/O port pins on the P89LPC9321 may be configured by software to one of
four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51 port
outputs), push-pull, open drain, and input-only. Two configuration registers for each port
select the output type for each port pin.
Quasi-bidirectional output type can be used as both an input and output without the need
to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is
weakly driven, allowing an external device to pull the pin LOW. When the pin is driven
LOW, it is driven strongly and able to sink a fairly large current. These features are
somewhat similar to an open-drain output except that there are three pull-up transistors in
the quasi-bidirectional output that serve different purposes.
The P89LPC9321 is a 3 V device, but the pins are 5 V-tolerant. In quasi-bidirectional
mode, if a user applies 5 V on the pin, there will be a current flowing from the pin to V
causing extra power consumption. Therefore, applying 5 V in quasi-bidirectional mode is
discouraged.
A quasi-bidirectional port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
The open-drain output configuration turns off all pull-ups and only drives the pull-down
transistor of the port driver when the port latch contains a logic 0. To be used as a logic
output, a port configured in this manner must have an external pull-up, typically a resistor
tied to V
Clock source
On-chip oscillator or watchdog
oscillator
External clock input
Low/medium/high speed
oscillator (external crystal or
resonator)
1. P1.5 (RST) can only be an input and cannot be configured.
2. P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or
open-drain.
DD
.
Number of I/O pins available
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 16 November 2010
8-bit microcontroller with accelerated two-clock 80C51 core
Reset option
No external reset (except during
power-up)
External RST pin supported
No external reset (except during
power-up)
External RST pin supported
No external reset (except during
power-up)
External RST pin supported
Table
7.
P89LPC9321
© NXP B.V. 2010. All rights reserved.
Number of I/O
pins (28-pin
package)
26
25
25
24
24
23
27 of 71
DD
,