KSZ8862 Micrel Semiconductor, KSZ8862 Datasheet - Page 125

• Manufacturer Part Number: KSZ8862
• Description: 2-port Ethernet Switch With Non-pci Interface And Fiber Support
• Manufacturer: Micrel Semiconductor

MDI-X Medium Dependent Interface Crossover
MIB
MII
NIC
NPVID Non Port VLAN ID
PLL
PME Power Management Event
QMU Queue Management Unit
SA
TDR Time Domain Reflectometry
UTP Unshielded Twisted Pair
VLAN Virtual Local Area Network
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can
reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s
Micrel, Inc.
April 2007
use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify
Management Information Base
Media Independent Interface
Network Interface Card
Phase-Locked Loop
Source Address
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL [phone] FAX [phone] WEB http://www.micrel.com
Micrel for any damages resulting from such use or sale.
© 2006 Micrel, Incorporated.
An Ethernet port connection that allows networked end stations (i.e.,
PCs or workstations) to connect to each other using a null-modem, or
crossover, cable. For 10/100 full-duplex networks, an end point (such as
a computer) and a switch are wired so that each transmitter connects to
the far end receiver. When connecting two computers together, a cable
that crosses the TX and RX is required to do this. With auto MDI-X, the
PHY senses the correct TX and RX roles, eliminating any cable
confusion.
The MIB comprises the management portion of network devices. This
can include things like monitoring traffic levels and faults (statistical),
and can also change operating parameters in network nodes (static
forwarding addresses).
The MII accesses PHY registers as defined in the IEEE 802.3
specification.
An expansion board inserted into a computer to allow it to be connected
to a network. Most NICs are designed for a particular type of network,
protocol, and media, although some can serve multiple networks.
The Port VLAN ID value is used as a VLAN reference.
An electronic circuit that controls an oscillator so that it maintains a
constant phase angle (i.e., lock) on the frequency of an input, or
reference, signal. A PLL ensures that a communication signal is locked
on a specific frequency and can also be used to generate, modulate,
and demodulate a signal and divide a frequency.
An occurrence that affects the directing of power to different
components of a system.
Manages packet traffic between MAC/PHY interface and the system
host. The QMU has built-in packet memories for receive and transmit
functions called TXQ (Transmit Queue) and RXQ (Receive Queue).
The address from which information has been sent.
TDR is used to pinpoint flaws and problems in underground and aerial
wire, cabling, and fiber optics. They send a signal down the conductor
and measure the time it takes for the signal -- or part of the signal -- to
return.
Commonly a cable containing 4 twisted pairs of wires. The wires are
twisted in such a manner as to cancel electrical interference generated
in each wire, therefore shielding is not required.
A configuration of computers that acts as if all computers are connected
by the same physical network but which may be located virtually
anywhere.
125
KSZ8862-16/32MQL
M9999-040407-3.0