KSZ8862 Micrel Semiconductor, KSZ8862 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/435/micrel_semiconductor_sml.jpg)
KSZ8862
Manufacturer Part Number
KSZ8862
Description
2-port Ethernet Switch With Non-pci Interface And Fiber Support
Manufacturer
Micrel Semiconductor
Datasheet
1.KSZ8862.pdf
(125 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
KSZ8862-16MQL-FX
Manufacturer:
Micrel Inc
Quantity:
135
Company:
Part Number:
KSZ8862-16MQL-FX
Manufacturer:
Micrel
Quantity:
67
Company:
Part Number:
KSZ8862-32MQL
Manufacturer:
Micrel
Quantity:
139
Company:
Part Number:
KSZ8862-32MQL-FX
Manufacturer:
Micrel Inc
Quantity:
135
Company:
Part Number:
KSZ8862-32MQL-FX
Manufacturer:
Micrel
Quantity:
258
Micrel, Inc.
April 2007
Pin
Number
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Pin Name
LDEVN
RDN
EECS
ARDY
CYCLEN
P2LED3
DGND
VDDCO
VLBUSN
EEEN
P1LED3
EEDO
EESK
EEDI
SWR
AEN
WRN
Type
Opd
Ipd
Opu
Opd
Ipd
Opd
Gnd
P
Ipd
Ipd
Opd
Opd
Opd
Ipd
Ipd
Ipu
Ipd
Pin Function
Active Low signal to host CPU to indicate an interrupt status bit is set, this pin need
an external 4.7K pull-up resistor.
Local Device Not
Active Low output signal, asserted when AEN is Low and A15-A4 decode to the
KSZ8862M address programmed into the high byte of the base address register.
LDEVN is a combinational decode of the Address and AEN signal.
Read Strobe Not
Asynchronous read strobe, active Low.
EEPROM Chip Select
Asynchronous Ready
ARDY may be used when interfacing asynchronous buses to extend bus access
cycles. It is asynchronous to the host CPU or bus clock. This pin needs an external
4.7K pull-up resistor.
Cycle Not
For VLBus-like mode cycle signal; this pin follows the addressing cycle to signal the
command cycle.
For burst mode (32-bit interface only), this pin stays High for read cycles and Low for
write cycles.
Port 2 LED indicator
See the description in pins 6, 7, and 8.
Digital IO ground
1.2V digital core voltage output (internal 1.2V LDO power supply output), this 1.2V
output pin provides power to VDDC, VDDA and VDDAP pins.
Note: Internally generated power voltage. Do not connect an external power supply
to this pin. This pin is used for connecting external filter (Ferrite bead and capacitors).
VLBus-like Mode
Pull-down or float: Bus interface is configured for synchronous mode.
Pull-up: Bus interface is configured for 8-bit or 16-bit asynchronous mode or EISA-
like burst mode.
EEPROM Enable
EEPROM is enabled and connected when this pin is pull-up.
EEPROM is disabled when this pin is pull-down or no connect.
Port 1 LED indicator. See the description in pins 3, 4, and 5.
EEPROM Data Out
This pin is connected to DI input of the serial EEPROM.
EEPROM Serial Clock
A 4
EEPROM Data In
This pin is connected to DO output of the serial EEPROM when EEEN is pull-up.
This pin can be pull-down for 8-bit bus mode, pull-up for 16-bus mode or don’t care
for 32-bus mode when EEEN is pull-down (without EEPROM).
Synchronous Write/Read
Write/Read signal for synchronous bus accesses. Write cycles when high and Read
cycles when low.
Address Enable
Address qualifier for the address decoding, active Low.
Write Strobe Not
µ
s serial output clock to load configuration data from the serial EEPROM.
13
KSZ8862-16/32MQL
M9999-040407-3.0