MCP6272 Microchip Technology Inc., MCP6272 Datasheet - Page 2

• Manufacturer Part Number: MCP6272
• Description: 170 ?a, 2 Mhz Rail-to-rail Op Am
• Manufacturer: Microchip Technology Inc.

MCP6271/1R/2/3/4/5
1.0
Absolute Maximum Ratings †
V
Current at Analog Input Pins (V
Analog Inputs (V
All other Inputs and Outputs .......... V
Difference Input Voltage ...................................... |V
Output Short Circuit Current .................................Continuous
Current at Output and Supply Pins ............................±30 mA
Storage Temperature....................................–65°C to +150°C
Junction Temperature (T
ESD Protection On All Pins (HBM/MM) ................ ≥ 4 kV/400V
DC ELECTRICAL SPECIFICATIONS
DS21810E-page 2
Electrical Characteristics: Unless otherwise indicated, T
V
Input Offset (Note 1)
Input Offset Voltage
Input Offset Voltage
Input Offset Temperature Drift
Power Supply Rejection Ratio
Input Bias Current and Impedance
Input Bias Current
Input Offset Current
Common Mode Input Impedance
Differential Input Impedance
Common Mode (Note 4)
Common Mode Input Voltage Range
Common Mode Rejection Ratio
Common Mode Rejection Ratio
Open-Loop Gain
DC Open-Loop Gain (Large Signal)
Note 1:
DD
OUT
(Extended Temperature)
– V
At Temperature
At Temperature
≈ V
2:
3:
4:
5:
6:
SS
ELECTRICAL
CHARACTERISTICS
DD
........................................................................7.0V
/2, R
Parameters
The MCP6275’s V
The current at the MCP6275’s V
This specification does not apply to the MCP6275’s V
The MCP6275’s V
V
has a voltage range specified by V
Set by design and characterization.
Does not apply to op amp B of the MCP6275.
DD
IN
L
– 100 mV. CMRR is not measured for op amp B of the MCP6275. The MCP6275’s V
+ and V
= 10 kΩ to V
J
) . .........................................+150°C
IN
–) †† .. V
IN
CM
INB
DD
+ and V
/2 and CS is tied low.
– pin (op amp B) has a common mode input voltage range (V
for op amp B (pins V
SS
SS
ΔV
– 1.0V to V
– 0.3V to V
IN
CMRR
CMRR
PSRR
V
V
Z
Sym
V
V
OS
Z
A
–) ...............±2 mA
I
DIFF
CMR
CMR
I
I
I
OS
CM
OS
OS
OL
B
B
B
/ΔT
INB
OH
A
– pin is specified by I
DD
DD
V
V
and V
DD
SS
SS
+ 1.0V
+ 0.3V
–3.0
–5.0
– V
Min
70
70
65
90
OUTA
—
—
—
—
—
—
—
− 0.15
− 0.30
OL
SS
A
.
/V
= +25°C, V
|
INB
+ and V
10
10
OUTA
±1.7
±1.0
±1.0
Typ
110
—
—
90
50
—
—
85
80
13
13
2
B
||6
||3
only.
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of
the device at those or any other conditions above those
indicated in the operational listings of this specification is not
implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
†† See Section 4.1.2 “Input Voltage and Current Limits”.
/V
DD
INB
INB
= +2.0V to +5.5V, V
–) is V
V
V
+ pin.
DD
DD
Max
+3.0
+5.0
200
—
—
—
—
—
—
—
—
—
+ 0.15
+ 0.30
5
SS
+ 100 mV.
µV/°C T
Units
Ω||pF Note 3
Ω||pF Note 3
mV
mV
dB
pA
pA
nA
pA
dB
dB
dB
V
V
SS
CMR
= GND, V
V
T
V
Note 2
T
T
Note 3
V
V
V
(Note 6)
V
(Note 6)
V
V
© 2006 Microchip Technology Inc.
A
A
A
A
CM
CM
DD
DD
CM
CM
OUT
CM
= +85°C (Note 2)
= +125°C (Note 2)
= –40°C to +125°C, V
= –40°C to +125°C, V
) of V
= 2.0V (Note 5)
= 5.5V (Note 5)
= –0.3V to 2.5V, V
= –0.3V to 5.3V, V
= V
= V
= V
OUTA
= 0.2V to V
SS
SS
SS
SS
CM
/V
Conditions
(Note 1)
+ 100 mV to
INB
= V
+ pin (op amp B)
DD
DD
/2,
– 0.2V,
DD
DD
CM
CM
= 5V
= 5V
= V
= V
SS
SS