hd64338342hw Renesas Electronics Corporation., hd64338342hw Datasheet - Page 345
hd64338342hw
Manufacturer Part Number
hd64338342hw
Description
Renesas 8-bit Single-chip Microcomputer H8 Family/h8/300l Super Low Power Series
Manufacturer
Renesas Electronics Corporation.
Datasheet
1.HD64338342HW.pdf
(719 pages)
- Current page: 345 of 719
- Download datasheet (7Mb)
Table 9.15 Input Capture Input Signal Input Edges Due to Input Capture Input Pin
Input Capture Input
Signal Input Edge
Generation of rising edge
Generation of falling edge
Note: When the P1
When performing noise canceler function switching by modifying NCS in port mode register 3
(PMR3), which controls the input capture input noise canceler, TMIG should first be cleared to 0.
Note that if NCS is modified without first clearing TMIG, an edge will be regarded as having been
input at the pin even though no valid edge has actually been input. Input capture input signal input
edges, and the conditions for their occurrence, are summarized in table 9.16.
Table 9.16 Input Capture Input Signal Input Edges Due to Noise Canceler Function
Input Capture Input
Signal Input Edge
Generation of rising edge
Generation of falling edge
Switching input capture input noise canceler function
signal is low.
Switching, and Conditions for Their Occurrence
Switching, and Conditions for Their Occurrence
3
pin is not set as an input capture input pin, the timer G input capture input
Conditions
When TMIG is modified from 0 to 1 while the TMIG pin is high
When NCS is modified from 0 to 1 while the TMIG pin is high, then
TMIG is modified from 0 to 1 before the signal is sampled five times by
the noise canceler
When TMIG is modified from 1 to 0 while the TMIG pin is high
When NCS is modified from 0 to 1 while the TMIG pin is low, then
TMIG is modified from 0 to 1 before the signal is sampled five times by
the noise canceler
When NCS is modified from 0 to 1 while the TMIG pin is high, then
TMIG is modified from 1 to 0 after the signal is sampled five times by
the noise canceler
Conditions
When the TMIG pin level is switched from low to high while TMIG is
set to 1, then NCS is modified from 0 to 1 before the signal is sampled
five times by the noise canceler
When the TMIG pin level is switched from high to low while TMIG is
set to 1, then NCS is modified from 1 to 0 before the signal is sampled
five times by the noise canceler
Rev. 6.00 Aug 04, 2006 page 309 of 680
REJ09B0145-0600
Section 9 Timers
Related parts for hd64338342hw
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Renesas Technology Corp [Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series]
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
RENESAS MCU M16C FAMILY / M16C/Tiny SERIES
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas Starter Kit for RX210
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas StarterKit for RX630
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit+ for RX63N
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
EVALBOARD/Renesas Starter Kit
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
FLASH PROGRAMMER FOR RENESAS MICROCONTROLLERS
Manufacturer:
Renesas Electronics Corporation.
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Manufacturer:
Renesas Electronics Corporation.
Datasheet: