lpc1778 NXP Semiconductors, lpc1778 Datasheet - Page 47

no-image

lpc1778

Manufacturer Part Number
lpc1778
Description
32-bit Arm Cortex-m3 Microcontroller; Up To 512 Kb Flash And 96 Kb Sram; Usb Device/host/otg; Ethernet; Lcd; Emc
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lpc1778FBD
Manufacturer:
NXP
Quantity:
20
Part Number:
lpc1778FBD144
Manufacturer:
TI
Quantity:
26
Part Number:
lpc1778FBD144
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
lpc1778FBD144
0
Company:
Part Number:
lpc1778FBD144
Quantity:
10 000
Part Number:
lpc1778FBD144,551
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
lpc1778FBD144551
Manufacturer:
nxp
Quantity:
4 030
Part Number:
lpc1778FBD144K
0
Part Number:
lpc1778FBD208
Manufacturer:
AIMTEC
Quantity:
1 200
Part Number:
lpc1778FBD208
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
lpc1778FBD208
0
Company:
Part Number:
lpc1778FBD208
Quantity:
4 800
Part Number:
lpc1778FBD208,551
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
lpc1778FET180
Manufacturer:
NXP
Quantity:
201
Part Number:
lpc1778FET208
Manufacturer:
NXP
Quantity:
201
Part Number:
lpc1778FET208
0
Part Number:
lpc1778FET208,551
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
LPC178x_7x
Objective data sheet
7.8.1 Features
7.8.2 Interrupt sources
7.10 External memory controller
7.8 Nested Vectored Interrupt Controller (NVIC)
7.9 Pin connect block
The NVIC is an integral part of the Cortex-M3. The tight coupling to the CPU allows for low
interrupt latency and efficient processing of late arriving interrupts.
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any pin on Port 0 and Port 2 regardless of the selected function can be programmed to
generate an interrupt on a rising edge, a falling edge, or both.
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
Most pins can also be configured as open-drain outputs or to have a pull-up, pull-down, or
no resistor enabled.
Remark: Supported memory size and type and EMC bus width vary for different parts
(see
Controls system exceptions and peripheral interrupts
In the LPC178x/7x, the NVIC supports 41 vectored interrupts
32 programmable interrupt priority levels, with hardware priority level masking
Relocatable vector table
Non-Maskable Interrupt (NMI)
Software interrupt generation
Table
2). The EMC pin configuration for each part is shown in
All information provided in this document is subject to legal disclaimers.
Rev. 00.04 — 8 July 2010
32-bit ARM Cortex-M3 microcontroller
LPC178x/7x
Table
© NXP B.V. 2010. All rights reserved.
7.
47 of 112

Related parts for lpc1778