xr16v2550im Exar Corporation, xr16v2550im Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16v2550im
Manufacturer Part Number
xr16v2550im
Description
High Performance Duart With 16-byte Fifo
Manufacturer
Exar Corporation
Datasheet
1.XR16V2550IM.pdf
(48 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16v2550im-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
xr16v2550im-F
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
REV. 1.0.2
Pin Description
Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain.
ANCILLARY SIGNALS
DSRB#
RESET
RTSB#
CTSB#
DTRB#
OP2B#
XTAL1
XTAL2
CDB#
N
RIB#
GND
GND
VCC
NC
AME
Center Pad
32-QFN
P
9, 17
15
16
10
11
24
26
13
IN
-
-
-
-
-
#
12, 24, 25,
48-TQFP
P
N/A
22
23
35
20
16
21
13
14
36
42
17
37
IN
9
#
T
Pwr
Pwr
Pwr
YPE
O
O
O
O
I
I
I
I
I
I
UART channel B Request-to-Send (active low) or general purpose out-
put. This port must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1], and IER[6].
UART channel B Clear-to-Send (active low) or general purpose input.
It can be used for auto CTS flow control, see EFR[7], and IER[7]. This
input should be connected to VCC when not used.
UART channel B Data-Terminal-Ready (active low) or general purpose
output. If it is not used, leave it unconnected.
UART channel B Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
UART channel B Carrier-Detect (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
UART channel B Ring-Indicator (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
Output Port 2 Channel B - The output state is defined by the user and
through the software setting of MCR[3]. INTB is set to the active mode
and OP2B# output LOW when MCR[3] is set to a logic 1. INTB is set to
the three state mode and OP2B# output HIGH when MCR[3] is set to a
logic 0. See MCR[3]. If INTB is used, this output should not be used as
a general output else it will disturb the INTB output functionality.
Crystal or external clock input.
Crystal or buffered clock output.
Reset (active high) - A longer than 40 ns HIGH pulse on this pin will
reset the internal registers and all outputs. The UART transmitter output
will be held HIGH, the receiver input will be ignored and outputs are
reset during reset period (see
2.25V to 3.6V power supply. All input pins are 5V tolerant.
Power supply common, ground.
The center pad on the backside of the 32-QFN package is metallic and
should be connected to GND on the PCB. The thermal pad size on the
PCB should be the approximate size of this center pad and should be
solder mask defined. The solder mask opening should be at least
0.0025" inwards from the edge of the PCB thermal pad.
No Connection.
5
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
D
Table 15
ESCRIPTION
).
XR16V2550