nrf24le1-f16q48-t ETC-unknow, nrf24le1-f16q48-t Datasheet - Page 180
![no-image](/images/no-image-200.jpg)
nrf24le1-f16q48-t
Manufacturer Part Number
nrf24le1-f16q48-t
Description
Ultra-low Power Wireless System On-chip Solution
Manufacturer
ETC-unknow
Datasheet
1.NRF24LE1-F16Q48-T.pdf
(191 pages)
- Current page: 180 of 191
- Download datasheet (2Mb)
nRF24LE1 Preliminary Product Specification
The nRF24LE1 has the following on-chip hardware debug support for a JTAG debugger:
These debug modules are available on device pins OCITO, OCTMS, OCITDO,OCITDI, OCITCK when
enabled in the flash InfoPage. The HW debug features can be interfaced to a PC and utilized in the Keil
Integrated Development Environment (IDE) by running nRFProbe found in the nRFgo development kits or
dedicated HW from First Silicon Solutions.
27.1
The features listed below are for the Keil µVision debugger only:
27.2
The JTAG debug interface is enabled by writing (through the flash SPI slave interface described in
6.3.4 on page
Flash Status Register (FSR bit 7,
The GPIO allocated in debug mode for each of the package alternatives is given in
130, but summarized in
A separate "Trigger Out" is available on the OCITO pin. This output can be activated when certain address
and data combinations occur.
Revision 1.1
27
•
•
•
•
•
•
•
•
•
•
•
•
•
•
nRFProbe hardware debugger from Nordic Semiconductor.
System Navigator from First Silicon Solutions (www.fs2.com).
Read/write all processor registers, SFR, program and data memory.
Go/halt processor run control.
Single step by assembly and C source instruction.
Four independent HW execution breakpoints.
Driver software for Keil µVision debugger interface.
Load binary, Intel Hex or OMF51 file formats.
Symbolic debug.
Load symbols, including code, variables and variable types.
Support C and assembly source code.
Source window can display C source and mixed mode.
Source window provides execution control; go, halt; goto cursor; step over/into call.
Source window can set or clear software and hardware breakpoints.
Note: A pull-up on OCITCK is required for the MCU to run (in debug mode) without the system nav-
HW debugger support
igator cable plugged in.
Features
Functional description
76) to address 0x24 in the infopage. Any byte value other than 0xFF enables debug. The
Table 113. HW debug physical interface for each nRF24LE1 package alternative
Table
OCITDO
OCITMS
OCITCK
OCITDI
OCITO
113..
Table 31. on page
24 pin 4x4
P0.6
P0.5
P0.4
P.03
P.02
180 of 191
75) shows the current status of the interface.
32 pin 5x5
P1.3
P1.2
P1.1
P1.0
P0.7
48 pin 7x7
P3.4
P3.3
P3.2
P3.1
P3.0
section 17.3 on page
section
Related parts for nrf24le1-f16q48-t
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AA05B-005L-120D](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet:
![HM3-65787H-5](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet: