DS80C320-ECD DALLAS [Dallas Semiconductor], DS80C320-ECD Datasheet - Page 145
DS80C320-ECD
Manufacturer Part Number
DS80C320-ECD
Description
High-Speed Microcontroller User Guide
Manufacturer
DALLAS [Dallas Semiconductor]
Datasheet
1.DS80C320-ECD.pdf
(175 pages)
- Current page: 145 of 175
- Download datasheet (2Mb)
High-Speed Microcontroller User’s Guide
the other. Setting either RCLK or TCLK to a logic 1 selects Timer 2 for baud rate generation. RCLK
and TCLK reside in T2CON.4 and TCON.5 respectively.
When using Timer 2 to generate baud rates, the formula will be as follows. Note that the reload value is a
16-bit number as compared with Timer 1, which uses only 8 bits.
o
Oscillator
Frequency
Mode 1, 3 baud rate =
32
*
(65536
RCAP2H,
RCAP2L)
Note that the 32 in the denominator is a result of the timer being run at a divide by 2, combined with the
divide by 16 applied to timer overflows as mentioned above. Timer 2 normally runs at a divide by either
12 or 4 in auto-reload mode. Setting RCLK or TCLK causes the divide by 2 operation.
This formula provides the derived baud rate for a given RCAP2H, RCAP2L and crystal. Most users
already know what baud rate is desired and want the timer reload value. Thus the equation solves as
follows.
Oscillator
Frequency
RCAP2H, RCAP2L = 65536 –
32
*
BaudRate
The Timer 2 interrupt is automatically disabled when either RCLK or TCLK is set. Also, the TF2
(TCON.7) flag will not be set on a timer rollover. The manual reload pin, T2EX (P1.1), will not cause a
reload either.
SERIAL I/O DESCRIPTION
A detailed description of each serial mode is given below. A description of framing error detection and
multiprocessor communication follows this section.
Mode 0
This mode is used to communicate in synchronous, half–duplex format with devices that accept the High-
Speed Microcontroller as a master. A functional block diagram and basic timing of this mode are shown
in Figure 12-1. As can be seen, there is one bidirectional data line (RXD) and one shift clock line (TXD)
used for communication. The shift clock is used to shift data into and out of the microcontroller and the
remote device. Mode 0 requires that the microcontroller is the master because the microcontroller
generates the serial shift clocks for both directions. As described above, the shift clock may be selected
to be either divide by 12 or divide by 4 of the oscillator as determined by the SM2 (SCON0.5 or
SCON1.5) bit.
145 of 175
Related parts for DS80C320-ECD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller, 8051 Comp., 4 8-Bit I/O Ports, 64K ROM/RAM, 25 MHz, 5 V, PLCC44
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller, 8051 Comp., 4 8-Bit I/O Ports, 64K ROM/RAM, 25 MHz, 5 V, PDIP40
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
High Resolution Temperature Measurement with Dallas Direct-to-Digital Temperature Sensors
Manufacturer:
Dallas Semiconductor
Part Number:
Description:
32.768kHz Temperature-Compensated Crystal Oscillator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
3.3 volt micromonitor, tolerance 20%
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Ultra3 LVD/SE SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet: