CN8330EPD CONEXANT [Conexant Systems, Inc], CN8330EPD Datasheet - Page 23
CN8330EPD
Manufacturer Part Number
CN8330EPD
Description
DS3/E3 Framer with 52 Mbps HDLC Controller
Manufacturer
CONEXANT [Conexant Systems, Inc]
Datasheet
1.CN8330EPD.pdf
(101 pages)
- Current page: 23 of 101
- Download datasheet (570Kb)
2.1.1 Brief Block Description
100441E
2.0 Functional Description
2.1 Overview
A block diagram of the circuit is illustrated in
B3ZS/HDB3 signal is decoded and the bipolar input is converted to a unipolar,
clocked serial data stream. Frame bit content is checked and the overhead bit data
links and alarms are extracted. The receive clock is provided at the receiver output
(RXCLK). The data is also connected to a Payload Parallel Data Link (PPDL)
receiver that decodes message blocks using the High-Level Data Link Control
(HDLC) format (Refer to Appendix A in this document for a description of the
HDLC formatter). The recovered data bytes are provided on a parallel output port
with a byte clock. The PPDL receiver can also be programmed to operate in
nibble mode or transparently without HDLC formatting.
enabled to reduce the jitter on the incoming data. The receive data is clocked into
the FIFO buffer after bipolar decoding. The FIFO buffer provides a Voltage
Controlled Oscillator (VCO) control signal to an external clock recovery circuit.
A dejittered clock (RXCKI) from the VCO is then used to read the data from the
FIFO buffer to the remaining receiver circuitry.
byte- or nibble-oriented data from the PPDL data port. DS3 overhead bits or E3
Frame Alignment Signal (FAS) bits are automatically inserted. Parallel data can
be formatted with idle flags, zero stuffing for transparency, and a selectable 16- or
32-bit Frame Check Sequence (FCS). Bytes or nibbles without HDLC formatting
can also be transmitted. The transmitter is able to send AIS, idle code, yellow
alarm, and all-ones signals. DS3 C-bits (or E3 N-bits) can be optionally inserted
into the data stream from an external source.
provided for the terminal data link in DS3 C-bit parity format and the E3 mode. In
C-bit mode, the three C-bits in subframe 5 of the M-frame are used for the
terminal data link. In E3 mode, the N-bit is used for the terminal data link.
indications in the received signal. For both DS3 and E3 modes, indications
include AIS, all-ones, and yellow alarm detection; and Out-of-Frame (OOF) and
frame bit error counting. In addition, loss of signal, idle code, and parity error
detection; line code violation (LCV), path parity, and FEBE event counting; and
parity and X-bit disagreement counting are provided for DS3 mode. The received
DS3 C-bits (or E3 N-bits) are available on an external pin to provide visibility for
external processing, if necessary.
A First In First Out (FIFO) memory buffer in the receive signal path can be
The transmitter is capable of sending either serial data from an external pin, or
LAPD (Link Access Procedure-D) receiver and transmitter circuitry is
The microprocessor interface or external outputs monitors all status
Conexant
2
Figure
2-1. The receive
2-1
Related parts for CN8330EPD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
V.34/Group 3 High Performance Fax Modem Family
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
SmartV.XX Modem
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Demodulator and FEC Decoder Low-power QPSK demodulator for worldwide satellite set-top box applications
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Dual Stream QPSK/BPSK Demodulator lC
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Single-Chip FTA and FTA-CI Set-Top Box System Solution
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Dual Digital Broadcast MPEG-2 Standard Definition TV Decoder with PVR Support
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Digital Broadcast High-Definition TV Decoder with PVR Support
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
MPEG-4 AVC/H.264 Video Decoder
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Dual Decode HDTV MPEG-2/H.264/VC-1 Video Decoder
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
VOICE PAIR GAIN FRAMER
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
ATM Transmitter/Receiver with UTOPIA Interface
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
integrated quad line interface unit unit for both 1.544 Mbps (T1) and 2.048 Mbps (E1) applications
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
V.34/Group 3 High Performance Fax Modem Family
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet:
Part Number:
Description:
SmartV.XX Modem
Manufacturer:
CONEXANT [Conexant Systems, Inc]
Datasheet: