MAX1245ACAP Maxim Integrated, MAX1245ACAP Datasheet - Page 9

• Manufacturer Part Number: MAX1245ACAP
• Description: Analog to Digital Converters - ADC Integrated Circuits (ICs)
• Manufacturer: Maxim Integrated

Specifications of MAX1245ACAP

• Number Of Channels: 8/4
• Architecture: SAR
• Conversion Rate: 100 KSPs
• Resolution: 12 bit
• Input Type: Single-Ended/Differential
• Snr: 70 dB
• Interface Type: 4-Wire (SPI, Microwire, QSPI, TMS320)
• Operating Supply Voltage: 2.375 V to 3.3 V
• Maximum Operating Temperature: + 70 C
• Package / Case: SSOP-20
• Maximum Power Dissipation: 640 mW
• Minimum Operating Temperature: 0 C
• Number Of Converters: 1
• Factory Pack Quantity: 66
• Voltage Reference: 2.048 V

where R
input signal, and t
that source impedances below 1kΩ do not significantly
affect the AC performance of the ADC. Higher source
impedances can be used if an input capacitor is con-
nected to the analog inputs, as shown in Figure 5. Note
that the input capacitor forms an RC filter with the input
source impedance, limiting the ADC’s signal bandwidth.
The ADC’s input tracking circuitry has a 2.25MHz
small-signal bandwidth, so it is possible to digitize
high-speed transient events and measure periodic sig-
nals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Internal protection diodes, which clamp the analog
input to V
swing from AGND - 0.3V to V
age. However, for accurate conversions near full scale,
the inputs must not exceed V
be lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off channels over two milliamperes, as excessive
current will degrade the conversion accuracy of the
on channel.
Figure 5. Quick-Look Circuit
ANALOG
IN
2.048V
INPUT
0V TO
DD
2.048V
= 12kΩ, R
and AGND, allow the channel input pins to
0.1µF
0.01µF
C1
_______________________________________________________________________________________
ACQ
S
= the source impedance of the
is never less than 2.0µs. Note
Analog Input Protection
VREF
CH7
MAX1245
DD
DD
by more than 50mV or
Input Bandwidth
+ 0.3V without dam-
SSTRB
DGND
AGND
SHDN
SCLK
DOUT
+2.375V, Low-Power, 8-Channel,
COM
V
DIN
CS
DD
N.C.
+2.5V
* FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FFF (HEX)
To quickly evaluate the MAX1245’s analog perfor-
mance, use the circuit of Figure 5. The MAX1245
requires a control byte to be written to DIN before each
conversion. Tying DIN to V
$FF (HEX), which trigger single-ended unipolar conver-
sions on CH7 in external clock mode without powering
down between conversions. In external clock mode, the
SSTRB output pulses high for one clock period before
the most significant bit of the 12-bit conversion result is
shifted out of DOUT. Varying the analog input to CH7
alters the sequence of bits from DOUT. A total of 15
clock cycles is required per conversion. All transitions
of the SSTRB and DOUT outputs occur on the falling
edge of SCLK.
A conversion is started by clocking a control byte into
DIN. With CS low, each rising edge on SCLK clocks a
bit from DIN into the MAX1245’s internal shift register.
After CS falls, the first arriving logic “1” bit defines the
MSB of the control byte. Until this first “start” bit arrives,
any number of logic “0” bits can be clocked into DIN
with no effect. Table 1 shows the control-byte format.
The MAX1245 is compatible with MICROWIRE, SPI, and
QSPI devices. For SPI, select the correct clock polarity
and sampling edge in the SPI control registers: set
CPOL = 0 and CPHA = 0. MICROWIRE, SPI, and QSPI
all transmit a byte and receive a byte at the same time.
Using the Typical Operating Circuit, the simplest soft-
ware interface requires only three 8-bit transfers to
0.1µF
+2.5V
OSCILLATOR
1.5MHz
Serial 12-Bit ADC
CH1
How to Start a Conversion
OSCILLOSCOPE
CH2
DD
feeds in control bytes of
CH3
CH4
Quick Look
SCLK
SSTRB
DOUT*
9