S25FL128SDPMFIG11 Spansion, S25FL128SDPMFIG11 Datasheet - Page 19

• Manufacturer Part Number: S25FL128SDPMFIG11
• Description: Flash 128Mb 3V 66MHz Serial NOR Flash
• Manufacturer: Spansion

Specifications of S25FL128SDPMFIG11

• Rohs: yes
• Data Bus Width: 1 bit
• Memory Type: Flash
• Memory Size: 128 Mbit
• Architecture: Uniform
• Timing Type: Asynchronous
• Interface Type: SPI
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.7 V
• Maximum Operating Current: 100 mA
• Operating Temperature: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SO-16

3.10
3.11
3.12
3.13
3.14
July 12, 2012 S25FL128S_256S_00_05
SI_or_IO_(during_input)
SO_or_IO_(external)
SO_or_IO_(internal)
Core Voltage Supply (V
Versatile I/O Power Supply (V
Supply and Signal Ground (V
Not Connected (NC)
Reserved for Future Use (RFU)
The HOLD# signal has an internal pull-up resistor and may be left unconnected in the host system if not used
for Quad mode.
V
functions including read, program, and erase. The voltage may vary from 2.7V to 3.6V.
The Versatile I/O (V
the host system to set the voltage levels that the device tolerates on all inputs and drives on outputs (address,
control, and IO signals). The V
For example, a V
to and from other 1.8V, 2.5V or 3V devices on the same data bus. V
signals operate at the same voltage as the core of the device. V
when not available the V
During the rise of power supplies the V
voltage. However, the V
> 1.65V, i.e. the V
power up, until the V
This supply is not available in all package options. For a backward compatible SO16 footprint, the V
is tied to V
V
drivers.
No device internal signal is connected to the package connector nor is there any future plan to use the
connector for a signal. The connection may safely be used for routing space for a signal on a Printed Circuit
Board (PCB). However, any signal connected to an NC must not have voltage levels higher than V
No device internal signal is currently connected to the package connector but is there potential future use of
the connector. It is recommended to not use RFU connectors for PCB routing channels so that the PCB may
take advantage of future enhanced features in compatible footprint devices.
HOLD#
SCLK
CC
SS
CS#
is the common voltage drain and ground reference for the device core, input signal receivers, and output
is the voltage source for all device internal logic. It is the single voltage used for all device internal
CC
inside the package; thus, the IO will function at V
Valid Input
IO
IO
IO
of 1.65V - 3.6V allows for I/O at the 1.8V, 2.5V or 3V levels, driving and receiving signals
supply voltage must not lag behind the V
IO
) supply is the voltage source for all device input receivers and output drivers and allows
A
A
supply voltage reaches its minimum operating level.
IO
IO
D a t a
supply voltage must also be above V
supply is tied to V
Figure 3.1 HOLD Mode Operation
CC
B
IO
S25FL128S and S25FL256S
)
range is 1.65V to V
Hold Condition
Standard Use
S h e e t
Don't Care
SS
IO
IO
)
supply voltage must remain less than or equal to the V
)
B
CC
internal to the package.
CC
Valid Input
B
. V
IO
cannot be greater than V
CC
C
CC
C
CC
IO
supply voltage by more than 200 mV during
level.
is not available in all package options,
-200 mV until the V
IO
Hold Condition
Non-standard Use
Don't Care
may be tied to V
D
CC
IO
CC
.
Valid Input
supply voltage is
so that interface
D
CC
IO
E
supply
IO
E
.
supply
19