CY7C1380D-167AXC Cypress Semiconductor Corp, CY7C1380D-167AXC Datasheet - Page 8
![IC SRAM 18MBIT 167MHZ 100LQFP](/photos/6/76/67624/428-100-tqfp_14x20x1_4_sml.jpg)
CY7C1380D-167AXC
Manufacturer Part Number
CY7C1380D-167AXC
Description
IC SRAM 18MBIT 167MHZ 100LQFP
Manufacturer
Cypress Semiconductor Corp
Type
Synchronousr
Datasheet
1.CY7C1380D-167AXC.pdf
(34 pages)
Specifications of CY7C1380D-167AXC
Memory Size
18M (512K x 36)
Package / Case
100-LQFP
Format - Memory
RAM
Memory Type
SRAM - Synchronous
Speed
167MHz
Interface
Parallel
Voltage - Supply
3.135 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Access Time
3.4 ns
Maximum Clock Frequency
167 MHz
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3.135 V
Maximum Operating Current
275 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Number Of Ports
4
Operating Supply Voltage
3.3 V
Density
18Mb
Access Time (max)
3.4ns
Sync/async
Synchronous
Architecture
SDR
Clock Freq (max)
167MHz
Operating Supply Voltage (typ)
3.3V
Address Bus
19b
Package Type
TQFP
Operating Temp Range
0C to 70C
Supply Current
275mA
Operating Supply Voltage (min)
3.135V
Operating Supply Voltage (max)
3.6V
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
100
Word Size
36b
Number Of Words
512K
Memory Configuration
1M X 18 / 512K X 36
Clock Frequency
167MHz
Supply Voltage Range
3.135V To 3.6V
Memory Case Style
TQFP
No. Of Pins
100
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
428-1629
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C1380D-167AXC
Manufacturer:
Cypress Semiconductor Corp
Quantity:
10 000
Part Number:
CY7C1380D-167AXC
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Company:
Part Number:
CY7C1380D-167AXCT
Manufacturer:
Cypress Semiconductor Corp
Quantity:
10 000
Functional Overview
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. Maximum
access delay from the clock rise (t
The
supports secondary cache in systems using a linear or inter-
leaved burst sequence. The interleaved burst order supports
Pentium and i486™ processors. The linear burst sequence suits
processors that use a linear burst sequence. The burst order is
user selectable, and is determined by sampling the MODE input.
Accesses can be initiated with either the processor address
strobe (ADSP) or the controller address strobe (ADSC). Address
advancement through the burst sequence is controlled by the
ADV input. A two-bit on-chip wraparound burst counter captures
the first address in a burst sequence and automatically incre-
ments the address for the rest of the burst access.
Byte write operations are qualified with the byte write enable
(BWE) and byte write select (BW
(GW) overrides all byte write inputs and writes data to all four
bytes. All writes are simplified with on-chip synchronous
self-timed write circuitry.
Three synchronous chip selects (CE
asynchronous output enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE
HIGH.
Single Read Accesses
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW,
(2) CE
signals (GW, BWE) are all deserted HIGH. ADSP is ignored if
CE
is stored into the address advancement logic and the address
register while being presented to the memory array. The corre-
sponding data is enabled to propagate to the input of the output
registers. At the rising edge of the next clock, the data is enabled
to propagate through the output register and onto the data bus
within 2.6 ns (250 MHz device) if OE is active LOW. The only
exception occurs when the SRAM is emerging from a deselected
state to a selected state; its outputs are always tri-stated during
the first cycle of the access. After the first cycle of the access,
the outputs are controlled by the OE signal. Consecutive single
read cycles are supported. Once the SRAM is deselected at
clock rise by the chip select and either ADSP or ADSC signals,
its output tri-states immediately.
Document #: 38-05543 Rev. *F
1
is HIGH. The address presented to the address inputs (A)
1
, CE
CY7C1380D/CY7C1382D/CY7C1380F/CY7C1382F
2
, CE
3
are all asserted active, and (3) the write
X
CO
) inputs. A global write enable
) is 2.6 ns (250 MHz device).
1
, CE
2
, CE
3
) and an
1
is
Single Write Accesses Initiated by ADSP
This access is initiated when both the following conditions are
satisfied at clock rise: (1) ADSP is asserted LOW and (2) CE
CE
A is loaded into the address register and the address
advancement logic while being delivered to the memory array.
The write signals (GW, BWE, and BW
ignored during this first cycle.
ADSP triggered write accesses require two clock cycles to
complete. If GW is asserted LOW on the second clock rise, the
data presented to the DQs inputs is written into the corre-
sponding address location in the memory array. If GW is HIGH,
then the write operation is controlled by BWE and BW
The
provides byte write capability that is described in the write cycle
descriptions table. Asserting the byte write enable input (BWE)
with the selected byte write (BW
the desired bytes. Bytes not selected during a byte write
operation remain unaltered. A synchronous self-timed write
mechanism has been provided to simplify the write operations.
The CY7C1380D/CY7C1382D/CY7C1380F/CY7C1382F is a
common I/O device, the output enable (OE) must be deserted
HIGH before presenting data to the DQs inputs. Doing so
tri-states the output drivers. As a safety precaution, DQs are
automatically tri-stated whenever a write cycle is detected,
regardless of the state of OE.
Single Write Accesses Initiated by ADSC
ADSC write accesses are initiated when the following conditions
are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deserted
HIGH, (3) CE
appropriate combination of the write inputs (GW, BWE, and
BW
byte(s). ADSC-triggered Write accesses require a single clock
cycle to complete. The address presented to A is loaded into the
address register and the address advancement logic while being
delivered to the memory array. The ADV input is ignored during
this cycle. If a global write is conducted, the data presented to
the DQs is written into the corresponding address location in the
memory core. If a byte write is conducted, only the selected bytes
are written. Bytes not selected during a byte write operation
remain unaltered. A synchronous self-timed write mechanism
has been provided to simplify the write operations.
The CY7C1380D/CY7C1382D/CY7C1380F/CY7C1382F is a
common I/O device, the output enable (OE) must be deserted
HIGH before presenting data to the DQs inputs. Doing so
tri-states the output drivers. As a safety precaution, DQs are
automatically tri-stated whenever a write cycle is detected,
regardless of the state of OE.
2
X
, and CE
) are asserted active to conduct a write to the desired
CY7C1380D/CY7C1382D/CY7C1380F/CY7C1382F
3
1
, CE
are all asserted active. The address presented to
2
, and CE
CY7C1380D, CY7C1382D
CY7C1380F, CY7C1382F
3
are all asserted active, and (4) the
X
) input, selectively writes to only
X
) and ADV inputs are
Page 8 of 34
X
signals.
1
[+] Feedback
,