NetduinoPlus2 Netduino, NetduinoPlus2 Datasheet - Page 126
NetduinoPlus2
Manufacturer Part Number
NetduinoPlus2
Description
Development Boards & Kits - ARM NETDUINO PLUS 2
Manufacturer
Netduino
Datasheet
1.STM32F407IGH6J.pdf
(180 pages)
Specifications of NetduinoPlus2
Rohs
yes
Product
Development Boards
Tool Is For Evaluation Of
STM32F405RG
Core
ARM Cortex M4
Interface Type
I2C, SPI, UART, USB
Operating Supply Voltage
7.5 v to 9 V
Data Bus Width
32 bit
Description/function
Arduino form factor
Dimensions
2.8 in x 2.1 in
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
- Current page: 126 of 180
- Download datasheet (3Mb)
Electrical characteristics
7. For external triggers, a delay of 1/f
Note:
126/180
Equation 1: R
The formula above
allowed for an error below 1/4 of LSB. N = 12 (from 12-bit resolution) and k is the number of
sampling periods defined in the ADC_SMPR1 register.
Table 68.
1. Better performance could be achieved in restricted V
2. Based on characterization, not tested in production.
3. If an inverted reset signal is applied to PDR_ON, this value can be lowered to 1.7 V when the device
ADC accuracy vs. negative injection current: injecting a negative current on any analog input
pins should be avoided as this significantly reduces the accuracy of the conversion being
performed on another analog input. It is recommended to add a Schottky diode (pin to
ground) to analog pins which may potentially inject negative currents.
Any positive injection current within the limits specified for I
Section 5.3.16
Symbol
a
operates in a reduced temperature range (0 to 70 °C).
EO
EG
ED
ET
EL
Total unadjusted error
Offset error
Gain error
Differential linearity error
Integral linearity error
ADC accuracy at f
AIN
does not affect the ADC accuracy.
PCLK2
Parameter
max formula
(Equation
must be added to the latency specified in
R
AIN
1) is used to determine the maximum external impedance
Doc ID 022152 Rev 3
=
ADC
------------------------------------------------------------- - R
f
ADC
= 30 MHz
f
f
V
PCLK2
ADC
DDA
×
C
(
= 30 MHz, R
k 0.5
= 1.8
ADC
= 60 MHz,
Test conditions
–
DD
(1)
×
(3)
, frequency and temperature ranges.
ln
to 3.6 V
)
(
2
N
AIN
+
2
< 10 kΩ,
Table
)
–
INJ(PIN)
STM32F405xx, STM32F407xx
67.
ADC
and ΣI
±1.5
±1.5
±1.5
Typ
±2
±1
INJ(PIN)
Max
±2.5
±3
±2
±5
±3
(2)
in
Unit
LSB
Related parts for NetduinoPlus2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Daughter Cards & OEM Boards POTENTIOMETER MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO 2
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO GO STARTER KIT
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO MINI
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards BUTTON MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards ETHERNET MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards SD CARD MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards RS-232 MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards XBEE ADAPTER MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards AMBIENT LIGHT MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO PLUS
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards GHI GADGETEER ADAPTER I/O BOARD
Manufacturer:
Netduino
Part Number:
Description:
IP DSL Access Multiplexer
Manufacturer:
Net to Net
Datasheet: