NetduinoPlus2 Netduino, NetduinoPlus2 Datasheet - Page 25
NetduinoPlus2
Manufacturer Part Number
NetduinoPlus2
Description
Development Boards & Kits - ARM NETDUINO PLUS 2
Manufacturer
Netduino
Datasheet
1.STM32F407IGH6J.pdf
(180 pages)
Specifications of NetduinoPlus2
Rohs
yes
Product
Development Boards
Tool Is For Evaluation Of
STM32F405RG
Core
ARM Cortex M4
Interface Type
I2C, SPI, UART, USB
Operating Supply Voltage
7.5 v to 9 V
Data Bus Width
32 bit
Description/function
Arduino form factor
Dimensions
2.8 in x 2.1 in
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
- Current page: 25 of 180
- Download datasheet (3Mb)
STM32F405xx, STM32F407xx
Figure 7.
Regulator OFF
This mode allows to power the device as soon as V
●
●
Regulator OFF/internal reset ON
This mode is available only on UFBGA and WLCSP90 packages. It is activated by
setting BYPASS_REG and PDR_ON pins to V
The regulator OFF/internal reset ON mode allows to supply externally a 1.2 V voltage
source through V
The following conditions must be respected:
–
–
–
In regulator OFF/internal reset ON mode, PA0 cannot be used as a GPIO pin since it
allows to reset the part of the 1.2 V logic which is not reset by the NRST pin, when the
internal voltage regulator in off.
Regulator OFF/internal reset OFF
This mode is available only on UFBGA and WLCSP packages. It is activated by setting
BYPASS_REG pin to V
V
between power domains.
If the time for V
reach 1.8 V, then PA0 should be connected to the NRST pin (see
Otherwise, PA0 should be asserted low externally during POR until V
1.8 V (see
If V
must be asserted on PA0 pin.
DD
Regulator ON/internal reset OFF
CAP_1
should always be higher than V
and V
Figure
CAP_1
CAP_1
CAP_2
9).
and V
DD
Doc ID 022152 Rev 3
and V
and by applying an inverted reset signal to PDR_ON, and
go below 1.08 V and V
CAP_2
CAP_2
pins, in addition to V
to reach 1.08 V is faster than the time for V
CAP_1
DD
DD
and V
.
DD
reaches 1.8 V.
is higher than 1.7 V, then a reset
CAP_2
DD
.
to avoid current injection
Figure
DD
Description
reaches
8).
25/180
DD
to
Related parts for NetduinoPlus2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Daughter Cards & OEM Boards POTENTIOMETER MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO 2
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO GO STARTER KIT
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO MINI
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards BUTTON MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards ETHERNET MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards SD CARD MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards RS-232 MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards XBEE ADAPTER MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards AMBIENT LIGHT MODULE NETDUINO GO
Manufacturer:
Netduino
Part Number:
Description:
Development Boards & Kits - ARM NETDUINO PLUS
Manufacturer:
Netduino
Part Number:
Description:
Daughter Cards & OEM Boards GHI GADGETEER ADAPTER I/O BOARD
Manufacturer:
Netduino
Part Number:
Description:
IP DSL Access Multiplexer
Manufacturer:
Net to Net
Datasheet: