LTC3417AIFE-1#PBF Linear Technology, LTC3417AIFE-1#PBF Datasheet - Page 4

• Manufacturer Part Number: LTC3417AIFE-1#PBF
• Description: IC BUCK SYNC ADJ 1A/1.5A 20TSSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC3417AIFE-1#PBF

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 0.8 ~ 5 V
• Current - Output: 1A, 1.5A
• Frequency - Switching: 1.5MHz, 0.6MHz ~ 4MHz
• Voltage - Input: 2.25 ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP Exposed Pad, 20-eTSSOP, 20-HTSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

LTC3417A-1
ELECTRICAL CHARACTERISTICS
TYPICAL PERFORMANCE CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC3417AE-1 is guaranteed to meet specifi ed performance
from 0°C to 85°C. Specifi cations over the –40°C to 85°C operating
ambient temperature range are assured by design, characterization
and correlation with statistical process controls. The LTC3417AI-1 is
guaranteed to meet performance specifi cations over the –40°C to 125°C
operating temperature range.
Note 3: The LTC3417A-1 is tested in feedback loop which servos V
the midpoint for the error amplifi er (V
for the error amplifi er (V
Note 4: Total supply current is higher due to the internal gate charge being
delivered at the switching frequency.
4
250mA/DIV
250mA/DIV
20mV/DIV
20mV/DIV
V
V
OUT
OUT
I
I
L
L
OUT1 Burst Mode Operation
OUT2 Burst Mode Operation
V
V
I
REFER TO FIGURE 4
V
V
I
REFER TO FIGURE 4
LOAD
LOAD
IN
OUT
IN
OUT
= 3.6V
= 3.6V
= 2.5V
= 1.8V
= 60mA
= 100mA
ITH2
2μs/DIV
2μs/DIV
= 0.6V).
ITH1
= 0.6V) and V
3417A-1 G04
3417A-1 G01
250mA/DIV
250mA/DIV
20mV/DIV
20mV/DIV
FB2
V
V
OUT
OUT
to the midpoint
I
I
L
L
OUT1 Pulse Skipping
Mode Operation
V
V
I
REFER TO FIGURE 4
OUT2 Pulse Skipping
Mode Operation
LOAD
V
V
I
REFER TO FIGURE 4
IN
OUT
LOAD
IN
OUT
= 3.6V
FB1
= 3.6V
= 1.8V
= 100mA
= 2.5V
= 60mA
to
2μs/DIV
2μs/DIV
Note 5: Switch on-resistance is guaranteed by design and test correlation
on the DHC package and by fi nal test correlation on the FE package.
Note 6: Variable frequency operation with resistor is guaranteed by design
but not production tested and is subject to duty cycle limitations.
Note 7: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specifi ed maximum operating junction
temperature may impair device reliability.
Note 8: T
dissipation, P
J
LTC3417AEDHC-1: T
LTC3417AEFE-1: T
is calculated from the ambient temperature, T
D
, according to the following formula:
3417A-1 G02
3417A-1 G05
250mA/DIV
250mA/DIV
20mV/DIV
20mV/DIV
V
V
J
OUT
OUT
= T
I
J
L
I
L
= T
A
V
V
I
REFER TO FIGURE 4
OUT1 Forced Continuous
Mode Operation
OUT2 Forced Continuous
Mode Operation
LOAD
IN
OUT
V
V
I
REFER TO FIGURE 4
+ (P
LOAD
A
IN
OUT
= 3.6V
+ (P
= 3.6V
= 1.8V
= 100mA
D
= 2.5V
= 60mA
• 38°C/W)
D
• 43°C/W)
2μs/DIV
2μs/DIV
A
, and power
3417A-1 G03
3417a1fa
3417A-1 G06