DS26528DK Maxim Integrated Products, DS26528DK Datasheet - Page 183
DS26528DK
Manufacturer Part Number
DS26528DK
Description
KIT DESIGN FOR DS26528
Manufacturer
Maxim Integrated Products
Datasheet
1.DS26528G.pdf
(276 pages)
Specifications of DS26528DK
Main Purpose
Telecom, Framer and Line Interface Units (LIUs)
Utilized Ic / Part
G575DS26528
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Secondary Attributes
-
Embedded
-
Primary Attributes
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 183 of 276
- Download datasheet (2Mb)
9.4.2 Transmit Register Definitions
Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit 7: Number of Flags Select (NOFS).
Bit 6: Transmit End of Message and Loop (TEOML). To loop on a message, this bit should be set to a one just
before the last data byte of an HDLC packet is written into the transmit FIFO. The message will repeat until the
user clears this bit or a new message is written to the transmit FIFO. If the host clears the bit, the looping message
will complete then flags will be transmitted until new message is written to the FIFO. If the host terminates the loop
by writing a new message to the FIFO the loop will terminate, one or two flags will be transmitted and the new
message will start. If not disabled via TCRCD, the transmitter will automatically append a 2-byte CRC code to the
end of all messages.
Bit 5: Transmit HDLC Reset (THR). Will reset the transmit HDLC controller and flush the transmit FIFO. An abort
followed by 7Eh or FFh flags/idle will be transmitted until a new packet is initiated by writing new data into the
FIFO. This is an acknowledged reset, that is, the host need only to set the bit and the DS26528 will clear it once
the reset operation is complete. Total time for the reset is less than 250μs.
Note: This bit will clear automatically if TMMR.INT_DONE has been set.
Bit 4: Transmit HDLC Mapping Select (THMS).
Bit 3: Transmit Flag/Idle Select (TFS). This bit selects the inter-message fill character after the closing and before
the opening flags (7Eh).
Bit 2: Transmit End of Message (TEOM). Should be set to a one just before the last data byte of an HDLC packet
is written into the transmit FIFO at THF. If not disabled via TCRCD, the transmitter will automatically append a
2-byte CRC code to the end of the message.
Bit 1: Transmit Zero Stuffer Defeat (TZSD). The zero stuffer function automatically inserts a zero in the message
field (between the flags) after five consecutive ones to prevent the emulation of a flag or abort sequence by the
data pattern. The receiver automatically removes (destuffs) any zero after five ones in the message field.
Bit 0: Transmit CRC Defeat (TCRCD). A 2-byte CRC code is automatically appended to the outbound message.
This bit can be used to disable the CRC function.
0 = send one flag between consecutive messages
1 = send two flags between consecutive messages
0 = Normal operation
1 = Reset transmit HDLC controller and flush the transmit FIFO
0 = Transmit HDLC assigned to channels
1 = Transmit HDLC assigned to FDL (T1 mode), Sa bits (E1 mode). This mode must be enabled with
TCR2.7.
0 = 7Eh
1 = FFh
0 = enable the zero stuffer (normal operation)
1 = disable the zero stuffer
0 = enable CRC generation (normal operation)
1 = disable CRC generation
NOFS
7
0
THC1
Transmit HDLC Control Register 1
110h + (200h x n): where n = 0 to 7, for Ports 1 to 8
TEOML
6
0
THR
5
0
183 of 276
THMS
4
0
TFS
3
0
DS26528 Octal T1/E1/J1 Transceiver
TEOM
2
0
TZSD
1
0
TCRCD
0
0
Related parts for DS26528DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: