M30873FHBGP#U3 Renesas Electronics America, M30873FHBGP#U3 Datasheet - Page 171

• Manufacturer Part Number: M30873FHBGP#U3
• Description: IC M32C/87 MCU FLASH 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M30873FHBGP#U3

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: EBI/EMI, I²C, IEBus, IrDA, SIO, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 384KB (384K x 8)
• Program Memory Type: FLASH
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M32C/87 Group (M32C/87, M32C/87A, M32C/87B)
REJ09B0180-0151 Rev.1.51 Jul 31, 2008
Page 147 of 587
Figure 13.8
<When using repeat transfer>
<When using repeat transfer>
i = 2, 3
NOTES:
1. When setting the DMiSL register, write a 1 to the DRQ bit.
2. The register bank 1 and high-speed interrupt cannot be used when using DMA2 and DMA3.
3. When the INT interrupts are selected as a DMA request source, do not write a 1 to the DCTi register. If the DCTi register is
4. Wait six CPU clock cycles or more by a program to set bits MDi1 and MDi0 to 01b or 11b after setting the DMiSL register.
5. When a DMA transfer is started by the software trigger, set both the DSR and DRQ bit in the DMiSL register to 1 at the
DMD1 register: bits MD21 and MD20 = 00b
DMiSL register: bits DSEL4 to DSEL0
B flag = 1
DMA2 (A0) register or DMA3 (A1) register
DSA2 (SB) register or DSA3 (FB) register
DRA2 (SVP) register or DRA3 (VCT) register
DCT2 (R0) register or DCT3 (R1) register
DRC2 (R2) register or DRC3 (R3) register
B flag = 0
DMD1 register: bits MD21 and MD20
1, do not generate a DMA request when writing 01b or 11b to bits MDi1 and MDi0.
same time.
used as DMAi request source
used as DMAi request source
Start the peripheral function
Register Settings When Using DMA2 or DMA3
Set the peripheral function
bits MD31 and MD30 = 00b
BW2 bit
RW2 bit
bits MD31 and MD30
BW3 bit
RW3 bit
DSR bit = 0
DRQ bit = 1
Start
End
Set the control registers of the peripheral function,
but do not yet start.
DMA disabled for channel 2
DMA disabled for channel 3
DMA request source select bits
DMA requested
Select register bank 1
Set an incremented source address or
incremented destination address
Set a fixed source address or
fixed destination address
Set an incremented source address or
incremented destination address
Set the number of transfer
Set the number of transfer, which is to be
reloaded
Select register bank 0
Transfer mode select bits for channel 2
Transfer unit select bit for channel 2
Transfer direction select bit for channel 2
Transfer mode select bits for channel 3
Transfer unit select bit for channel 3
Transfer direction select bit for channel 3
(note 5)
(2)
(2)
(3)
Write with LDC instruction
Write with MOV instruction
Write with LDC instruction
Write with LDC instruction
Write with MOV instruction
Write with MOV instruction
Write with LDC instruction
(note 4)
(note 1)
13. DMAC