M30873FHBGP#U3 Renesas Electronics America, M30873FHBGP#U3 Datasheet - Page 386

• Manufacturer Part Number: M30873FHBGP#U3
• Description: IC M32C/87 MCU FLASH 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M30873FHBGP#U3

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: EBI/EMI, I²C, IEBus, IrDA, SIO, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 384KB (384K x 8)
• Program Memory Type: FLASH
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M32C/87 Group (M32C/87, M32C/87A, M32C/87B)
REJ09B0180-0151 Rev.1.51 Jul 31, 2008
Page 362 of 587
Figure 22.31
22.3.5
Table 22.12
NOTE:
Waveform generation channels
OUTC2_i pin
Waveform output start condition
Waveform output stop condition
Interrupt request generation timing An interrupt request is generated at the second clock cycle after the base timer
Selectable function
1. Channels 0 to 7 are provided in the 144-pin package. Channels 0 to 2 are provided in the 100-pin package.
The OUTC2_i pin (i = 0 to 7) outputs the value of the RTPi bit in the G2RTP register when the base timer value
matches the G2POi register. To use real-time output mode, set the RTP bit in the G2POCRi register to 1 and the
PRT bit to 0 in the channel used for this mode. Also, set the PRP bit in the G2BCR1 register to 0.
Table 22.12 lists specifications of real-time port output mode. Figure 22.31 shows a block diagram. Figure
22.32 shows an example of real-time port output mode operation.
Real-Time Port Output Mode (Group 2)
Item
G2PO0 register
G2PO6 register
G2PO7 register
Specifications of Real-Time Port Output Mode
Real-Time Port Output Function Block Diagram
Base timer
Group 2: channels 0 to 7
Real-time port output
Set both the BTS bit in the G2BCR1 register and the IFEi bit in the G2FE register
to 1
Set either the BTS or IFEi bit to 0
value matches the G2POi register value.
• Initial value set function:
The PO2iR bit in the IIOkIR register (k = 3, 5 to 11) becomes 1 (interrupt
requested) when an interrupt request is generated.
(See Figure 11.18 IIO0IR to IIO11IR Registers)
Set the initial output level when waveform output is started (determined by the
IVL bit in the G2POCRi register)
G2RTP register
RTP0
RTP6
RTP7
(1)
22. Intelligent I/O (Waveform Generation Function)
IVL bit in the
IVL bit in the
IVL bit in the
G2POCR0
G2POCR6
G2POCR7
Specification
D Q
D Q
D Q
S
R
S
R
S
R
Real-time port output
OUTC2_0
OUTC2_6
OUTC2_7