MC9S08GT60ACFBE Freescale Semiconductor, MC9S08GT60ACFBE Datasheet - Page 265

• Manufacturer Part Number: MC9S08GT60ACFBE
• Description: IC MCU 60K FLASH 4K RAM 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT60ACFBE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 36
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8/2.08V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PQFP
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 39
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 1.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

1
2
3
4
5
6
7
8
Freescale Semiconductor
dc injection current
Input capacitance (all non-supply pins)
Typicals are measured at 25°C.
This parameter is characterized and not tested on each device.
Measurement condition for pull resistors: V
Power supply must maintain regulation within operating V
conditions. If positive injection current (V
in external power supply going out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or
if clock rate is very low which would reduce overall power consumption.
All functional non-supply pins are internally clamped to V
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive and negative clamp voltages, then use the larger of the two values.
This parameter is characterized and not tested on each device.
IRQ does not have a clamp diode to V
Single pin limit
Total MCU limit, includes sum of all stressed pins
0.8
0.6
0.4
0.2
V
1
0
40
35
30
25
20
IN
0
1.8
< V
SS
2
–40°C
, V
85°C
25°C
Figure A-2. Typical Low-Side Driver (Sink) Characteristics (Ports C and F)
IN
2.2
4, 5, 6, 7, 8
Parameter
Figure A-1. Pullup and Pulldown Typical Resistor Values (V
> V
PULLUP RESISTOR TYPICALS
TYPICAL V
2.4
DD
10
2.6
I
OL
V
DD
OL
(mA)
(V)
VS I
2.8
(Temperature Range = –40 to 85°C Ambient)
Table A-4. DC Characteristics (Sheet 3 of 3)
OL
(2)
DD
AT V
In
3
. Do not drive IRQ above V
20
> V
DD
MC9S08GB60A Data Sheet, Rev. 2
In
3.2
= V
= 3.0 V
DD
) is greater than I
SS
3.4
–40°C
for pullup and V
85°C
25°C
3.6
Symbol
SS
DD
|I
C
IC
30
In
and V
|
range during instantaneous and operating maximum current
DD
DD
0.4
0.3
0.2
0.1
DD
, the injection current may flow out of V
In
DD
40
35
30
25
20
.
0
= V
load will shunt current greater than maximum injection
1.8
.
1
Min
—
—
—
DD
for pulldown.
–40°C
85°C
25°C
2.3
PULLDOWN RESISTOR TYPICALS
Typical
2
TYPICAL V
Appendix A Electrical Characteristics
I
OL
DD
V
V
= 3 mA
DD
1
DD
= 3.0 V)
(V)
(V)
OL
2.8
I
OL
VS V
= 6 mA
3
Max
0.2
DD
5
7
DD
and could result
3.3
I
OL
–40°C
85°C
25°C
= 10 mA
4
Unit
mA
mA
3.6
pF
265