LAN9313-NZW SMSC, LAN9313-NZW Datasheet - Page 197

• Manufacturer Part Number: LAN9313-NZW
• Description: Ethernet ICs Three Port 10/100 Ethernet Switch
• Manufacturer: SMSC
• Type: Three Port Managed Ethernet Switchr

Specifications of LAN9313-NZW

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 Mbps, 100 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 0 V
• Supply Current (max): 155 mA, 270 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Three Port 10/100 Managed Ethernet Switch with MII
Datasheet
SMSC LAN9313/LAN9313i
BITS
0
Port 0 Full-Duplex Manual Flow Control Select (MANUAL_FC_MII)
This bit toggles flow control selection between manual and auto-negotiation.
0: If auto-negotiation is enabled, the auto-negotiation function
determines the flow control of switch Port 0 (RX_FC_MII and
TX_FC_MII values ignored). If auto-negotiation is disabled, the
RX_FC_MII and TX_FC_MII values are used.
1: TX_FC_MII and RX_FC_MII bits determine the flow control of switch
Port 0 when in full-duplex mode
Note:
Note 13.12 The default value of this field is determined by the BP_EN_strap_mii configuration strap.
Note 13.13 The default value of this bit is determined by multiple strap settings. The strap values are
Note 13.14 The default value of this field is determined by the FD_FC_strap_mii configuration strap.
Note 13.15 This bit is RO when in MAC mode.
Note 13.16 The default value of this field is determined by the manual_FC_strap_mii configuration
In MAC mode, this bit is forced high. The Virtual PHY is not
applicable in this mode and full-duplex flow control should be
controlled manually by the host based on the external PHYs Auto-
Negotiation results.
The strap value is loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the value, this register is updated with the new values. See
Section 4.2.4, "Configuration Straps," on page 45
loaded during reset and can be re-written by the EEPROM Loader. Once the EEPROM
Loader re-writes the values, this register is updated with the new values. Refer to
6.2.3, "Flow Control Enable Logic," on page 60
The strap value is loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the value, this register is updated with the new values. See
Section 4.2.4, "Configuration Straps," on page 45
strap. The strap value is loaded during reset and can be re-written by the EEPROM
Loader. Once the EEPROM Loader re-writes the value, this register is updated with the
new values. In MAC mode, this bit is not re-written by the EEPROM Loader and has a
default value of “1”. See
information.
DESCRIPTION
DATASHEET
Section 4.2.4, "Configuration Straps," on page 45
197
for additional information.
for more information.
for more information.
Note 13.15
TYPE
R/W
Revision 1.7 (06-29-10)
Note 13.16
DEFAULT
for more
Section