LAN9313-NZW SMSC, LAN9313-NZW Datasheet - Page 398

• Manufacturer Part Number: LAN9313-NZW
• Description: Ethernet ICs Three Port 10/100 Ethernet Switch
• Manufacturer: SMSC
• Type: Three Port Managed Ethernet Switchr

Specifications of LAN9313-NZW

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 Mbps, 100 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 0 V
• Supply Current (max): 155 mA, 270 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 16 Datasheet Revision History
Revision 1.7 (06-29-10)
REVISION LEVEL & DATE
Rev. 1.7 (06-29-10)
Rev. 1.6 (08-19-09)
Rev. 1.5 (10-28-08)
Rev. 1.3 (07-03-08)
Table 3.6, “EEPROM Pins,”
on page 37
Table 3.6, “EEPROM Pins,”
on page 37
Section 13.1.7.4, "Virtual
PHY Identification LSB
Register (VPHY_ID_LSB),"
on page 215
13.2.2.4, "Port x PHY
Identification LSB Register
(PHY_ID_LSB_x)," on
page 238
Section 13.3.2.23, "Port x
MAC Transmit Configuration
Register
(MAC_TX_CFG_x)," on
page 290
Table 6.1, “Switch Fabric
Flow Control Enable Logic,”
on page 61
Figure 14.2 nRST Reset Pin
Timing on page 389
All
Section 13.1.3.1, "EEPROM
Command Register
(E2P_CMD)," on page 160
Section 14.6, "Clock
Circuit," on page 393
All
Port x PHY Special
Control/Status Register
(PHY_SPECIAL_CONTROL
_STATUS_x) on page 252
Port x PHY Auto-Negotiation
Advertisement Register
(PHY_AN_ADV_x) on page
239
Section 14.6, "Clock
Circuit," on page 393
SECTION/FIGURE/ENTRY
Table 16.1 Customer Revision History
and
DATASHEET
Section
398
Added note to EE_SDA and EE_SCL pin
descriptions stating “If I
pull-up is required when using an EEPROM and is
recommended if no EEPROM is attached.”
Added note to EEDO/EEPROM_TYPE pin
descriptions stating “When not using a Microwire
or I
recommended on this pin.”
Clarified default values using binary.
Added note to IFG Config field description:
Note:
Corrected rightmost column title to “TX FLOW
CONTROL ENABLE”
Updated figure shading.
Standard SMSC formatting applied.
Corrected CFG_LOADED bit type from “RO” to
“R/WC”
Changed max ESR value from 30 to 50 Ohms and
corrected typos in operating temerpature range.
Fixed various typos
Updated RESERVED bits 11:5 definition to
“RESERVED - Write as 0000010b, ignore on
read”, changed default to 0000010b, and made
field R/W.
Bits 15 and 9 made RESERVED.
Changed minimum drive level from 0.5mW to
300uW
2
C EEPROM, an external pull-down resistor is
IFG Config values less than 15 are
unsupported.
Three Port 10/100 Managed Ethernet Switch with MII
CORRECTION
2
C is selected, an external
SMSC LAN9313/LAN9313i
Datasheet