PIC18F86K90-I/PT Microchip Technology, PIC18F86K90-I/PT Datasheet - Page 364

• Manufacturer Part Number: PIC18F86K90-I/PT
• Description: 64kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TRA
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F86K90-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87K90 FAMILY
22.2.5
The EUSART module has the capability of sending the
special Break character sequences that are required by
the LIN/J2602 bus standard. The Break character
transmit consists of a Start bit, followed by twelve ‘0’
bits and a Stop bit. The Frame Break character is sent
whenever the SENDB and TXEN bits (TXSTAx<3> and
TXSTAx<5>, respectively) are set while the Transmit
Shift Register is loaded with data. Note that the value
of data written to TXREGx will be ignored and all ‘0’s
will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN/J2602 specification).
Note that the data value written to the TXREGx for the
Break character is ignored. The write simply serves the
purpose of initiating the proper sequence.
The TRMT bit indicates when the transmit operation is
active or Idle, just as it does during normal transmis-
sion. See Figure 22-10 for the timing of the Break
character sequence.
22.2.5.1
The following sequence will send a message frame
header made up of a Break, followed by an Auto-Baud
Sync byte. This sequence is typical of a LIN/J2602 bus
master.
FIGURE 22-10:
DS39957B-page 364
Reg. Empty Flag)
Reg. Empty Flag)
Reg. Empty Flag)
Write to TXREGx
(Transmit Buffer
(Transmit Shift
(Transmit Shift
BRG Output
(Shift Clock)
SENDB bit
TRMT bit
TXx (pin)
TXxIF bit
BREAK CHARACTER SEQUENCE
Break and Sync Transmit Sequence
SEND BREAK CHARACTER SEQUENCE
Dummy Write
SENDB Sampled Here
Start Bit
Bit 0
Preliminary
Bit 1
Break
1.
2.
3.
4.
5.
When the TXREGx becomes empty, as indicated by
the TXxIF, the next data byte can be written to
TXREGx.
22.2.6
The Enhanced USART module can receive a Break
character in two ways.
The first method forces configuration of the baud rate
at a frequency of 9/13 the typical speed. This allows for
the Stop bit transition to be at the correct sampling
location (13 bits for Break versus Start bit and 8 data
bits for typical data).
The second method uses the auto-wake-up feature
described in Section 22.2.4 “Auto-Wake-up on Sync
Break Character”. By enabling this feature, the
EUSART will sample the next two transitions on
RXx/DTx, cause an RCxIF interrupt and receive the
next data byte followed by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Rate Detect
feature. For both methods, the user can set the ABDEN
bit once the TXxIF interrupt is observed.
Configure the EUSART for the desired mode.
Set the TXEN and SENDB bits to set up the
Break character.
Load the TXREGx with a dummy character to
initiate transmission (the value is ignored).
Write ‘55h’ to TXREGx to load the Sync
character into the transmit FIFO buffer.
After the Break has been sent, the SENDB bit is
reset by hardware. The Sync character now
transmits in the preconfigured mode.
RECEIVING A BREAK CHARACTER
Bit 11
Auto-Cleared
 2010 Microchip Technology Inc.
Stop Bit