PIC18F45J10-I/ML Microchip Technology Inc., PIC18F45J10-I/ML Datasheet - Page 28

• Manufacturer Part Number: PIC18F45J10-I/ML
• Description: 44 PIN, 32 KB FLASH, 1024 RAM
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F45J10-I/ML

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 32
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin QFN
• Programmable Memory: 32K Bytes
• Ram Size: 1K Bytes
• Speed: 40 MHz
• Timers: 1-8 bit, 2-16 bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F45J10 FAMILY
2.5
The PIC18F45J10 family of devices includes an inter-
nal oscillator source (INTRC) which provides a nominal
31 kHz output. The INTRC is enabled on device
power-up and clocks the device during its configuration
cycle until it enters operating mode. INTRC is also
enabled if it is selected as the device clock source or if
any of the following are enabled:
• Fail-Safe Clock Monitor
• Watchdog Timer
• Two-Speed Start-up
These features are discussed in greater detail in
Section 20.0 “Special Features of the CPU”.
The INTRC can also be optionally configured as the
default clock source on device start-up by setting the
FOSC2 configuration bit. This is discussed in
Section 2.6.1 “Oscillator Control Register”.
2.6
The PIC18F45J10 family includes a feature that allows
the device clock source to be switched from the main
oscillator to an alternate clock source. PIC18F45J10
family devices offer two alternate clock sources. When
an alternate clock source is enabled, the various
power-managed operating modes are available.
Essentially, there are three clock sources for these
devices:
• Primary oscillators
• Secondary oscillators
• Internal oscillator
FIGURE 2-5:
DS39682B-page 26
T1OSO
T1OSI
OSC2
OSC1
Internal Oscillator Block
Clock Sources and
Oscillator Switching
Primary Oscillator
Secondary Oscillator
PIC18F45J10 FAMILY CLOCK DIAGRAM
T1OSCEN
Enable
Oscillator
Sleep
Preliminary
PIC18F45J10 Family
Source
INTRC
The primary oscillators include the External Crystal
and Resonator modes and the External Clock modes.
The particular mode is defined by the FOSC2:FOSC0
configuration bits. The details of these modes are
covered earlier in this chapter.
The secondary oscillators are those external sources
not connected to the OSC1 or OSC2 pins. These
sources may continue to operate even after the
controller is placed in a power-managed mode.
PIC18F45J10 family devices offer the Timer1 oscillator
as a secondary oscillator. This oscillator, in all
power-managed modes, is often the time base for
functions such as a real-time clock.
Most often, a 32.768 kHz watch crystal is connected
between the RC0/T1OSO/T13CKI and RC1/T1OSI
pins. Loading capacitors are also connected from each
pin to ground.
The Timer1 oscillator is discussed in greater detail in
Section 11.3 “Timer1 Oscillator”.
In addition to being a primary clock source, the internal
oscillator is available as a power-managed mode
clock source. The INTRC source is also used as the
clock source for several special features, such as the
WDT and Fail-Safe Clock Monitor.
The clock sources for the PIC18F45J10 family devices
are shown in Figure 2-5. See Section 20.0 “Special
Features of the CPU” for Configuration register
details.
4 x PLL
Internal Oscillator
HSPLL, ECPLL
FOSC2:FOSC0
HS, EC
T1OSC
© 2006 Microchip Technology Inc.
Clock Source Option
for other Modules
WDT, PWRT, FSCM
and Two-Speed Start-up
Control
Clock
OSCCON<1:0>
Peripherals
IDLEN
CPU