NUC130LE3CN Nuvoton Technology Corporation of America, NUC130LE3CN Datasheet - Page 332

• Manufacturer Part Number: NUC130LE3CN
• Description: IC MCU 32BIT 128KB FLASH 48LQFP
• Manufacturer: Nuvoton Technology Corporation of America
• Series: NuMicro™ NUC100r

Specifications of NUC130LE3CN

• Core Processor: ARM Cortex-M0
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The UART0 and UART1 controllers support auto-flow control function that uses two low-level
signals, /CTS (clear-to-send) and /RTS (request-to-send), to control the flow of data transfer
between the UART and external devices (ex: Modem). When auto-flow is enabled, the UART is
not allowed to receive data until the UART asserts /RTS to external device. When the number of
bytes in the RX FIFO equals the value of RTS_TRI_LEV (UA_FCR [19:16]), the /RTS is de-
asserted. The UART sends data out when UART controller detects /CTS is asserted from external
device. If a valid asserted /CTS is not detected the UART controller will not send data out.
The UART controllers also provides Serial IrDA (SIR, Serial Infrared) function (User must set
IrDA_EN (UA_FUN_SEL [1]) to enable IrDA function). The SIR specification defines a short-range
infrared asynchronous serial transmission mode with one start bit, 8 data bits, and 1 stop bit. The
maximum data rate is 115.2 Kbps (half duplex). The IrDA SIR block contains an IrDA SIR
Protocol encoder/decoder. The IrDA SIR protocol is half-duplex only. So it cannot transmit and
receive data at the same time. The IrDA SIR physical layer specifies a minimum 10ms transfer
delay between transmission and reception. This delay feature must be implemented by software.
The alternate function of UART controllers is LIN (Local Interconnect Network) function. The LIN
mode is selected by setting the LIN_EN bit in UA_FUN_SEL register. In LIN mode, one start bit
and 8-bit data format with 1-bit stop bit are required in accordance with the LIN standard.
For NuMicro™ NUC100 Series, another alternate function of UART controllers is RS-485 9-bit
mode function, and direction control provided by RTS pin or can program GPIO (PB.2 for RTS0
and PB.6 for RTS1) to implement the function by software. The RS-485 mode is selected by
setting the UA_FUN_SEL register to select RS-485 function. The RS-485 driver control is
implemented using the RTS control signal from an asynchronous serial port to enable the RS-485
driver. In RS-485 mode, many characteristics of the RX and TX are same as UART.
230400
115200
57600
38400
19200
9600
4800
NuMicro™ NUC130/NUC140 Technical Reference Manual
A=142
A=286
A=10
A=22
A=34
A=70
A=4
Table 5-9 UART Baud Rate Setting Table
0x0000_000A
0x0000_008E
0x0000_011E
0x0000_0004
0x0000_0016
0x0000_0022
0x0000_0046
A=190,B=11
A=142,B=15
A=382,B=11
A=286,B=15
A=10,B=15
A=14,B=11
A=22,B=15
A=30,B=11
A=46,B=11
A=34,B=15
A=126,B=8
A=94,B=11
A=70,B=15
A=254,B=8
A=510,B=8
A=4,B=15
A=6,B=11
A=62,B=8
- 332 -
0x2B00_000E
0x2B00_001E
0x2B00_00BE
0x2B00_017E
0x2B00_0006
0x2F00_000A
0x2800_003E
0x2B00_002E
0x2800_007E
0x2B00_005E
0x2800_00FE
0x2F00_008E
0x2800_01FE
0x2F00_011E
0x2F00_0004
0x2F00_0016
0x2F00_0022
0x2F00_0046
Publication Release Date: June 14, 2011
A=1150
A=2302
A=4606
A=190
A=382
A=574
A=94
0x3000_00BE
0x3000_005E
0x3000_017E
0x3000_023E
0x3000_047E
0x3000_08FE
0x3000_11FE
Revision V2.01