AT90PWM216 Atmel Corporation, AT90PWM216 Datasheet - Page 280

• Manufacturer Part Number: AT90PWM216
• Manufacturer: Atmel Corporation

Specifications of AT90PWM216

• Flash (kbytes): 16 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

25. Memory Programming
25.1
7710F–AVR–09/11
Program And Data Memory Lock Bits
For details about these two section, see
and
Table 24-8.
Note:
The AT90PWM216/316 provides six Lock bits which can be left unprogrammed (“1”) or can be
programmed (“0”) to obtain the additional features listed in
erased to “1” with the Chip Erase command.
Table 25-1.
Variable
PCMSB
PAGEMSB
ZPCMSB
ZPAGEMSB
PCPAGE
PCWORD
BLB12
BLB11
BLB02
BLB01
LB2
LB1
“RWW – Read-While-Write Section” on page 268
Lock Bit Byte
1. Z15:Z14: always ignored
Z0: should be zero for all SPM commands, byte select for the LPM instruction.
See
Z-pointer during Self-Programming.
Explanation of Different Variables used in
pointer
Lock Bit Byte
“Addressing the Flash During Self-Programming” on page 273
PC[12:6]
PC[5:0]
12
5
(1)
Corresponding
Bit No
Z-value
7
6
5
4
3
2
1
0
Z13:Z7
Z6:Z1
Z13
Z6
(1)
“NRWW – No Read-While-Write Section” on page 268
Description
–
–
Boot Lock bit
Boot Lock bit
Boot Lock bit
Boot Lock bit
Lock bit
Lock bit
Description
Most significant bit in the Program Counter. (The
Program Counter is 12 bits PC[11:0])
Most significant bit which is used to address the
words within one page (32 words in a page requires
5 bits PC [4:0]).
Bit in Z-register that is mapped to PCMSB. Because
Z0 is not used, the ZPCMSB equals PCMSB + 1.
Bit in Z-register that is mapped to PAGEMSB.
Because Z0 is not used, the ZPAGEMSB equals
PAGEMSB + 1.
Program counter page address: Page select, for
page erase and page write
Program counter word address: Word select, for
filling temporary buffer (must be zero during page
write operation)
Figure 24-3
Table
AT90PWM216/316
25-2. The Lock bits can only be
Default Value
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
and the Mapping to the Z-
for details about the use of
280