AT90PWM216 Atmel Corporation, AT90PWM216 Datasheet - Page 300

• Manufacturer Part Number: AT90PWM216
• Manufacturer: Atmel Corporation

Specifications of AT90PWM216

• Flash (kbytes): 16 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Table 25-16. Serial Programming Instruction Set (Continued)
Note:
25.9.4
7710F–AVR–09/11
Instruction
Write Fuse High bits
Write Extended Fuse Bits
Read Fuse bits
Read Fuse High bits
Read Extended Fuse Bits
Read Calibration Byte
Poll RDY/BSY
a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = don’t care
SPI Serial Programming Characteristics
For characteristics of the SPI module see “SPI Serial Programming Characteristics” on page
300.
1010 1100
1010 1100
0101 0000
0101 1000
0101 0000
0011 1000
1111 0000
Byte 1
1010 1000
1010 0100
0000 0000
0000 1000
0000 1000
000x xxxx
0000 0000
Byte 2
Instruction Format
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
0000 0000
xxxx xxxx
Byte 3
iiii iiii
xxxx xxii
oooo oooo
oooo oooo
oooo oooo
oooo oooo
xxxx xxxo
Byte4
Operation
Set bits = “0” to program, “1” to
unprogram. See
284
Set bits = “0” to program, “1” to
unprogram. See
282
Read Fuse bits. “0” = programmed, “1”
= unprogrammed. See Table XXX on
page XXX for details.
Read Fuse High bits. “0” = pro-
grammed, “1” = unprogrammed. See
Table 25-5 on page 284
Read Extended Fuse bits. “0” = pro-
grammed, “1” = unprogrammed. See
Table 25-4 on page 282
Read Calibration Byte
If o = “1”, a programming operation is
still busy. Wait until this bit returns to
“0” before applying another command.
AT90PWM216/316
for details.
for details.
Table 25-5 on page
Table 25-4 on page
for details.
for details.
300