ST72561J6-Auto STMicroelectronics, ST72561J6-Auto Datasheet - Page 274
ST72561J6-Auto
Manufacturer Part Number
ST72561J6-Auto
Description
8-bit MCU for automotive
Manufacturer
STMicroelectronics
Datasheet
1.ST72561R9-AUTO.pdf
(324 pages)
Specifications of ST72561J6-Auto
Hdflash Endurance
100 cycles, data retention 20 years at 55 °C
5 Power Saving Modes
halt, auto wake up from halt, active halt, wait and slow
- Current page: 274 of 324
- Download datasheet (3Mb)
Electrical characteristics
20.2.2
20.2.3
274/324
Current characteristics
1. All power (V
2.
3. Negative injection disturbs the analog performance of the device. See note in
4. When several inputs are submitted to a current injection, the maximum
Thermal characteristics
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
pads, there is no positive injection current, and the corresponding V
characteristics.
positive and negative injected currents (instantaneous values). These results are based on
characterization with
I
I
INJ(PIN)
ΣI
INJ(PIN)
Symbol
Symbol
INJ(PIN)
T
I
I
VDD
VSS
I
STG
T
IO
J
must never be exceeded. This is implicitly insured if V
(2)(3)
(2)
DD
) and ground (V
Total current into V
Total current out of V
Output current sunk by any standard I/O and
control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control
pin
Injected current on V
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on PB3 (on Flash devices)
Injected current on any other pin
Total injected current (sum of all I/O and control
pins)
Storage temperature range
Maximum junction temperature (see
Σ
I
INJ(PIN)
IN
(4)
>V
DD
SS
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
) lines must always be connected to the external supply.
Doc ID 12370 Rev 8
DD
Ratings
Ratings
SS
PP
power lines (source)
ground lines (sink)
pin
(4)
Section 21.3: Thermal
IN
maximum is respected. If V
IN
(1)
(1)
maximum must always be respected.
Σ
I
INJ(PIN)
IN
INJ(PIN)
< V
Maximum value
Section 20.13: 10-bit ADC
SS
-65 to +150
is the absolute sum of the
. For true open-drain
value. A positive
Value
150
±25
-25
+5
25
50
±5
±5
characteristics)
ST72561-Auto
IN
maximum
Unit
Unit
mA
°C
Related parts for ST72561J6-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-BIT MCU WITH FLASH OR ROM, 10-BIT ADC, 5 TIMERS, SPI, LINSCI(TM), ACTIVE CAN
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: