M24LR64-R-DW6T/2 STMICROELECTRONICS [STMicroelectronics], M24LR64-R-DW6T/2 Datasheet - Page 37
M24LR64-R-DW6T/2
Manufacturer Part Number
M24LR64-R-DW6T/2
Description
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.M24LR64-R-DW6T2.pdf
(126 pages)
- Current page: 37 of 126
- Download datasheet (937Kb)
M24LR64-R
7.1
Commands
The M24LR64-R supports the following commands:
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Inventory, used to perform the anticollision sequence.
Stay Quiet, used to put the M24LR64-R in quiet mode, where it does not respond to
any inventory command.
Select, used to select the M24LR64-R. After this command, the M24LR64-R
processes all Read/Write commands with Select_flag set.
Reset To Ready, used to put the M24LR64-R in the ready state.
Read Block, used to output the 32 bits of the selected block and its locking status.
Write Block, used to write the 32-bit value in the selected block, provided that it is not
locked.
Read Multiple Blocks, used to read the selected blocks and send back their value.
Write AFI, used to write the 8-bit value in the AFI register.
Lock AFI, used to lock the AFI register.
Write DSFID, used to write the 8-bit value in the DSFID register.
Lock DSFID, used to lock the DSFID register.
Get System Info, used to provide the system information value
Get Multiple Block Security Status, used to send the security status of the selected
block.
Initiate, used to trigger the tag response to the Inventory Initiated sequence.
Inventory Initiated, used to perform the anticollision sequence triggered by the Initiate
command.
Write-sector Password, used to write the 32 bits of the selected password.
Lock-sector Password, used to write the Sector security status bits of the selected
sector.
Present-sector Password, enables the user to present a password to unprotect the
user blocks linked to this password.
Fast Initiate, used to trigger the tag response to the Inventory Initiated sequence.
Fast Inventory Initiated, used to perform the anticollision sequence triggered by the
Initiate command.
Fast Read Single Block, used to output the 32 bits of the selected block and its
locking status.
Fast Read Multiple Blocks, used to read the selected blocks and send back their
value.
Doc ID 15170 Rev 8
RF device operation
37/126
Related parts for M24LR64-R-DW6T/2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
64 Kbit Eeprom With Password Protection & Dual Interface 400 Khz I?c Serial Bus & Iso 15693 Rf Protocol At 13.56 Mhz
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
13.56MHZ 64KBIT EEPROM SO8N
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
13.56MHZ 64KBIT EEPROM UFDFPN8
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
13.56MHZ 64KBIT EEPROM 8 TSSOP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EEPROM Dual Interface 64k EEPROM ISO15693-I2C
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EEPROM, 64K, DUAL INTERFACE, 8TSSOP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EEPROM, 64K, DUAL INTERFACE, 8SOIC
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
64 Kbit EEPROM with password protection & dual interface
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet: