ATMEGA8535L-8JU Atmel, ATMEGA8535L-8JU Datasheet - Page 154

• Manufacturer Part Number: ATMEGA8535L-8JU
• Description: MCU AVR 8K ISP FLASH MEM 44-PLCC
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8535L-8JU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 512Byte
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PLCC
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Parity Generator
Disabling the Transmitter
154
ATmega8535(L)
interrupt-driven data transmission is used, the Data Register Empty interrupt routine
must either write new data to UDR in order to clear UDRE or disable the Data Register
Empty interrupt, otherwise a new interrupt will occur once the interrupt routine
terminates.
The Transmit Complete (TXC) Flag bit is set to one when the entire frame in the transmit
Shift Register has been shifted out and there are no new data currently present in the
transmit buffer. The TXC Flag bit is automatically cleared when a transmit complete
interrupt is executed, or it can be cleared by writing a one to its bit location. The TXC
Flag is useful in half-duplex communication interfaces (like the RS-485 standard), where
a transmitting application must enter receive mode and free the communication bus
immediately after completing the transmission.
When the Transmit Compete Interrupt Enable (TXCIE) bit in UCSRB is set, the USART
Transmit Complete Interrupt will be executed when the TXC Flag becomes set (pro-
vided that global interrupts are enabled). When the transmit complete interrupt is used,
the interrupt handling routine does not have to clear the TXC Flag, this is done automat-
ically when the interrupt is executed.
The parity generator calculates the parity bit for the serial frame data. When parity bit is
enabled (UPM1 = 1), the Transmitter Control Logic inserts the parity bit between the last
data bit and the first stop bit of the frame that is sent.
The disabling of the Transmitter (setting the TXEN to zero) will not become effective
until ongoing and pending transmissions are completed (i.e., when the transmit Shift
Register and Transmit Buffer Register do not contain data to be transmitted). When dis-
abled, the Transmitter will no longer override the TxD pin.
2502K–AVR–10/06