PIC17C44-16/P Microchip Technology, PIC17C44-16/P Datasheet - Page 80

• Manufacturer Part Number: PIC17C44-16/P
• Description: IC MCU OTP 8KX16 PWM 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C44-16/P

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 16MHz
• Connectivity: UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 454 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC17
• No. Of I/o's: 33
• Ram Memory Size: 454Byte
• Cpu Speed: 16MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 2
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC17
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 33
• Interface Type: SCI/USART
• Number Of Timers: 4
• Embedded Interface Type: USART
• Rohs Compliant: Yes
• Processor Series: PIC17C
• Core: PIC
• Data Ram Size: 454 B
• Maximum Clock Frequency: 16 MHz
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• Data Rom Size: 454 B
• Height: 4.95 mm
• Length: 53.21 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Width: 14.73 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA17XP401 - DEVICE ADAPTER FOR PIC17C42AAC174001 - MODULE SKT PROMATEII 40DIP
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

PIC17C4X
12.2.3
When TMR3CS is set, the 16-bit TMR3 increments on
the falling edge of clock input TCLK3. The input on the
RB5/TCLK3 pin is sampled and synchronized by the
internal phase clocks twice every instruction cycle. This
causes a delay from the time a falling edge appears on
TCLK3 to the time TMR3 is actually incremented. For
the external clock input timing requirements, see the
Electrical Specification section. Figure 12-9 shows the
timing diagram when operating from an external clock.
12.2.4
Since Timer3 is a 16-bit timer and only 8-bits at a time
can be read or written, care should be taken when
reading or writing while the timer is running. The best
method to read or write the timer is to stop the timer,
perform any read or write operation, and then restart
Timer3 (using the TMR3ON bit). However, if it is neces-
sary to keep Timer3 free-running, care must be taken.
For writing to the 16-bit TMR3, Example 12-2 may be
used. For reading the 16-bit TMR3, Example 12-3 may
be used. Interrupts must be disabled during this rou-
tine.
FIGURE 12-9: TMR1, TMR2, AND TMR3 OPERATION IN EXTERNAL CLOCK MODE
DS30412C-page 80
PR1, PR2, or PR3H:PR3L
TMR1, TMR2, or TMR3
EXTERNAL CLOCK INPUT FOR TIMER3
READING/WRITING TIMER3
Instruction
executed
Read_TMR
WR_TMR
TCLK12
TMRxIF
Note 1: TCLK12 is sampled in Q2 and Q4.
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
'A9h'
34h
3: The latency from TCLK12
indicates a sampling point.
Write to TMRx
MOVWF
TMRx
35h
Read TMRx
MOVFP
TMRx,W
A8h
EXAMPLE 12-2: WRITING TO TMR3
BSF
MOVFP RAM_L,
MOVFP RAM_H,
BCF
EXAMPLE 12-3: READING FROM TMR3
MOVPF
MOVPF
MOVFP
CPFSLT
RETURN
MOVPF
MOVPF
RETURN
to timer increment is between 2Tosc and 6Tosc.
Read TMRx
MOVFP
TMRx,W
CPUSTA, GLINTD ;Disable interrupt
CPUSTA, GLINTD ;Done,enable interrupt
TMR3L, TMPLO
TMR3H, TMPHI
TMPLO, WREG
TMR3L, WREG
TMR3L, TMPLO
TMR3H, TMPHI
A9h
TMR3L
TMR3H
;
;
1996 Microchip Technology Inc.
;read low tmr0
;read high tmr0
;tmplo
;tmr0l < wreg?
;no then return
;read low tmr0
;read high tmr0
;return
'A9h'
00h
wreg