C8051F34A-GM Silicon Laboratories Inc, C8051F34A-GM Datasheet - Page 180

• Manufacturer Part Number: C8051F34A-GM
• Description: IC 8051 MCU 64K FLASH MEM 32-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F34A-GM

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4352 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 32QFN EP
• Device Core: 8051
• Family Name: C8051F34x
• Maximum Speed: 48 MHz
• Cpu Family: C8051F34x
• Device Core Size: 8b
• Frequency (max): 48MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 25
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1350-5

C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
16.11. Configuring Endpoints1-3
Endpoints1-3 are configured and controlled through their own sets of the following control/status registers:
IN registers EINCSRL and EINCSRH, and OUT registers EOUTCSRL and EOUTCSRH. Only one set of
endpoint control/status registers is mapped into the USB register address space at a time, defined by the
contents of the INDEX register (USB Register Definition 16.4).
Endpoints1-3 can be configured as IN, OUT, or both IN/OUT (Split Mode) as described in
The endpoint mode (Split/Normal) is selected via the SPLIT bit in register EINCSRH.
When SPLIT = ‘1’, the corresponding endpoint FIFO is split, and both IN and OUT pipes are available.
When SPLIT = ‘0’, the corresponding endpoint functions as either IN or OUT; the endpoint direction is
selected by the DIRSEL bit in register EINCSRH.
16.12. Controlling Endpoints1-3 IN
Endpoints1-3 IN are managed via USB registers EINCSRL and EINCSRH. All IN endpoints can be used
for Interrupt, Bulk, or Isochronous transfers. Isochronous (ISO) mode is enabled by writing ‘1’ to the ISO bit
in register EINCSRH. Bulk and Interrupt transfers are handled identically by hardware.
An Endpoint1-3 IN interrupt is generated by any of the following conditions:
16.12.1.Endpoints1-3 IN Interrupt or Bulk Mode
When the ISO bit (EINCSRH.6) = ‘0’ the target endpoint operates in Bulk or Interrupt Mode. Once an end-
point has been configured to operate in Bulk/Interrupt IN mode (typically following an Endpoint0
SET_INTERFACE command), firmware should load an IN packet into the endpoint IN FIFO and set the
INPRDY bit (EINCSRL.0). Upon reception of an IN token, hardware will transmit the data, clear the
INPRDY bit, and generate an interrupt.
180
Bit7:
Bits6–0: E0CNT: Endpoint 0 Data Count
Bit7
R
-
1. An IN packet is successfully transferred to the host.
2. Software writes ‘1’ to the FLUSH bit (EINCSRL.3) when the target FIFO is not empty.
3. Hardware generates a STALL condition.
USB Register Definition 16.18. E0CNT: USB0 Endpoint 0 Data Count
Unused. Read = 0; Write = don’t care.
This 7-bit number indicates the number of received data bytes in the Endpoint 0 FIFO. This
number is only valid while bit OPRDY is a ‘1’.
Bit6
R
Bit5
R
Bit4
R
Rev. 1.3
E0CNT
Bit3
R
Bit2
R
Bit1
R
Bit0
R
Section 16.5.1
USB Address:
00000000
Reset Value
0x16
.